Rosemount 8732C Manual Download Page 84 | Manualshive

Page: 84 / 126

background image

Rosemount Model 8732C Integral Mount Magnetic Flowmeter System

7-4

Performance
Specifications

(System specifications at reference conditions with frequency output and flowtube in new condition.)

Accuracy (with Model 8712C, Model 8712U or Model 8732C)

±0.5% of rate from 1 to 30 ft/s (0.3 to 10 m/s). Includes combined effects of
linearity, hysteresis, repeatability, and calibration uncertainty. Accuracy is
±0.005 ft/s (±0.0015 m/s) from low-flow cutoff to 1.0 ft/s (0.3 m/s).

Vibration Effect

Meets IEC 770 Pipeline Installation Conditions.

Mounting Position Effect

None when installed to ensure flowtube remains full.

Physical
Specifications

Non-Wetted Materials

Flow Tube

AISI Type 304 SST.

Flanges

Carbon steel or AISI Type 304 SST.

Housing

Welded steel.

Paint

Polyurethane.

Process Wetted Materials

Lining

PTFE Teflon, ETFE Tefzel, polyurethane, neoprene, or natural rubber.

Electrodes

316L SST, Hastelloy C-276, tantalum, platinum-10% iridium, titanium.

Process Connections

AISI Type 304 SST – includes ANSI Class 150 flange to Tri-Clover Tri-Clamp
3-A quick-disconnect ferrule.

Process Connections

ANSI Class 150 or ANSI Class 300

½ through 24 inch.

AWWA Class 125

30- and 36-inch.

DIN PN 10, 16, 25, and 40

PN40 Standard Flange for 15–80 mm.

PN16 Standard Flange for 100–150 mm.

PN10 Standard Flange for 200–600 mm.

Electrical Connections

Two ¾–14 NPT connections are provided in the terminal enclosure for
electrical wiring.

Grounding Rings

Grounding rings are installed between the flange and the tube face on both ends
of the flowtube. They have an I.D. slightly larger than the flowtube I.D. and an
external tab to attach ground wiring. Grounding rings are available in 316L
stainless steel, Hastelloy C-276, titanium, and tantalum.

Grounding Electrode

A grounding electrode is installed similarly to the measurement electrodes
through the flowtube lining. It is available in 316L stainless steel,
Hastelloy C-276, titanium, tantalum or platinum.

Flowtube Dimensions

See Tables 7-3 and 7-4; Figures 7-1 and 7-2.

«
...
82
83
84
85
86
...
»

Summary of Contents for 8732C































































































































Reviews:

No comments

Related manuals for 8732C

Brand: OHAUS Pages: 26

Brand: Keeler Pages: 68

Brand: Bamo Pages: 17

Brand: HBM Pages: 84

Brand: SATO KEIRYOKI Pages: 2

Brand: Parker Pages: 16

Brand: Waterproof Pages: 51

Brand: Omega Pages: 100

FrameSaver SLV Series

Brand: Paradyne Pages: 39

Brand: Opus Technologies Pages: 24

Brand: SBS Pages: 17

Brand: UNI-T Pages: 2

CR-2010 PRO Series

Brand: G-Tek Pages: 48

Brand: Vega Pages: 20

Brand: Milkotester Pages: 44

Brand: PCE Health and Fitness Pages: 66

BioTector B3500C

Brand: Hach Pages: 165

Brand: Omega Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands