Rosemount 8732C Manual Download Page 25 | Manualshive

Page: 25 / 126

background image

2-13

Installation

Model 8711

For Model 8711, the flowtube inside diameter should be centered with
respect to the inside diameter of the adjoining upstream and
downstream piping. This will ensure the flowmeter achieves its
specified accuracy. Mounting bolts supplied with 0.15 through 1-inch
(4–25 mm) line sizes are specifically sized to properly align these
flowtubes with the flange configurations specified. For 1.5 through
8-inch (40–200 mm) line sizes, two centering rings are supplied for
alignment purposes. Place the centering rings over the flowtube using
the following instructions as a reference. If you received two centering
sleeves, follow the steps described under Alignment with
Centering Sleeves.

Alignment with Centering Rings

1. Insert the two studs for the bottom side of the flowtube between

the pipe flanges.

2. Place the two centering rings over each end of the flowtube.

3. Place the flowtube between the flanges. Make sure that the

centering rings are properly placed in the studs. The
studs should be aligned with the markings on the rings that
correspond to the flange you are using.

4. Insert the remaining studs, and install the washers and nuts.

5. Tighten the nuts to the specifications listed in Table 2-4.

NOTE

On the 4- and 6-inch PN 10–16, the installer will need to insert the
flowtube with rings first and then insert the studs. The slots on this
ring scenario are located on the inside of the ring.

FIGURE 2-12. Alignment with Centering Rings.

Centering Ring

Gasket for Tefzel/Teflon-lined

Flowtubes only

(Supplied by Customer)

Installation Studs, Nuts, and Washers

FLOW

Centering Ring

«
...
23
24
25
26
27
...
»

Summary of Contents for 8732C































































































































Reviews:

No comments

Related manuals for 8732C

Brand: Campbell Pages: 25

Brand: Larson Davis Pages: 2

Brand: G-Tek Pages: 27

Brand: A&D Pages: 74

Brand: WAGER Pages: 36

BML SL1-ALZ-ZZ Series

Brand: Balluff Pages: 26

Brand: Campbell Pages: 362

Brand: Campbell Pages: 60

Brand: Campbell Pages: 116

Brand: Campbell Pages: 30

Brand: Campbell Pages: 55

Network Card-MS

Brand: Eaton Pages: 26

Brand: J.P. Instruments Pages: 9

Brand: J.ASSY Pages: 13

Brand: E+E Elektronik Pages: 20

Brand: Brooks Pages: 64

Brand: brena Pages: 26

Brand: sebaKMT Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands