manualshive.com logo in svg

Rosemount 8732C, Manual

The Rosemount 8732C is a versatile and high-performance instrument designed for precision measurement in various industries. This user-friendly device is coupled with a comprehensive manual, which you can easily download for free from our website. Unlock the full potential of your Rosemount 8732C with our detailed manual.

Share
Download
background image

iii

SECTION 4:
Transmitter Functions

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Safety Messages   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Review Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Check Output Variables  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Process Variables  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Basic Configuration   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Units  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Line Size  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Tube Cal. Number   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Upper Range Value   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Special Units Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Volume Unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Base Volume Unit   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Conversion Number  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Base Time Unit   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Flow Rate Unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Analog Output Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Upper Range Value (URV) . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Lower Range Value (LRV)  . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4–20 mA Output Trim  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Loop Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Digital Output  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Auxiliary Output Control   . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Pulse Width   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Totalizer Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Totalizer Display   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Noise Reduction   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Damping  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Coil Frequency  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Auto Zero   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Low Flow Cutoff  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Signal Processing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Signal Processing Control  . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Number of Samples  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Maximum Percent Limit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Time Limit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Calibration   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

Gain (Electronics) Trim  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

Transmitter Information Configuration   . . . . . . . . . . . . . . . . . . . . . . 4-15

Transmitter Tag  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Software Revision Number  . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Descriptor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Message   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Date   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Flowtube Tag   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Flowtube Serial Number  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Liner Material   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Electrode Type  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Electrode Material  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Flange Type   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Flange Material  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Multidrop Communications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18

Auto Poll  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Poll Address  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

Summary of Contents for 8732C































































































































Reviews:

No comments

Related manuals for 8732C

Farfisa Compact Owner'S Manual preview
Compact
Brand: Farfisa Pages: 14
Valmet TS Installation And Owner'S Manual preview
TS
Brand: Valmet Pages: 63
TANDBERG 15 Series General And Technical Information preview
15 Series
Brand: TANDBERG Pages: 53
janitza UMG 96-S2 Quick Manual preview
UMG 96-S2
Brand: janitza Pages: 6
janitza UMG 804 Installation Manual preview
UMG 804
Brand: janitza Pages: 36
YOKOGAWA BT200 User Manual preview
BT200
Brand: YOKOGAWA Pages: 53
SICK DUSTHUNTER C200 Installation Operation & Maintenance preview
DUSTHUNTER C200
Brand: SICK Pages: 126
mru NOVAplus biogas User Manual preview
NOVAplus biogas
Brand: mru Pages: 78
Vega VEGAWAVE Supplementary Instructions Manual preview
VEGAWAVE
Brand: Vega Pages: 20
Polimaster PM1703GNA-II Operation Manual preview
PM1703GNA-II
Brand: Polimaster Pages: 24
Waves GRAND RHAPSODY PIANO User Manual preview
GRAND RHAPSODY PIANO
Brand: Waves Pages: 19
Righton Retinomax K+Screeen Instructions Manual preview
Retinomax K+Screeen
Brand: Righton Pages: 112
aboni HydroTracer FLV HT2 Operation Manual preview
HydroTracer FLV HT2
Brand: aboni Pages: 48
Bird Electronic Thruline 4020 Series Instruction Book preview
Thruline 4020 Series
Brand: Bird Electronic Pages: 59
LaserLiner MoistureMaster Compact Plus Manual preview
MoistureMaster Compact Plus
Brand: LaserLiner Pages: 80
SIGRIST StackGuard Instruction Manual preview
StackGuard
Brand: SIGRIST Pages: 54
Phonak Serenity Classic SafetyMeter User Manual preview
Serenity Classic SafetyMeter
Brand: Phonak Pages: 48
Global Test Supply DOUBLE VISION DDPM-40 Quick Start Manual preview
DOUBLE VISION DDPM-40
Brand: Global Test Supply Pages: 12

Brands by name

Popular brands

Load more brands