Rosemount 8732C Manual Download Page 54 | Manualshive

Page: 54 / 126

background image

Rosemount Model 8732C Integral Mount Magnetic Flowmeter System

4-8

DIGITAL OUTPUT

Pulse Output Scaling equates one transistor switch closure pulse to a
selectable number of volume units. The volume unit used for scaling
pulse output is taken from the numerator of the configured flow units.
For example, if gal/min had been chosen when selecting the flow rate
unit, the volume unit displayed would be gallons.

NOTE

The scaled pulse output is designed to operate between 0 and 1000 Hz.
The electronics will not accept a conversion factor that would result in a
pulse frequency outside that range. The minimum conversion factor
value is found by dividing the upper range value (in units of volume per
second) by 1000 Hz.

When selecting pulse output scaling, remember that the maximum
pulse rate is 1000 Hz. With the 110 percent overrange capability, the
absolute limit is 1100 Hz. For example, if you want the Model 8732C to
pulse every time 0.01 gallons pass through the flowtube, and the flow
rate is 1000 gal/min, you will exceed the 1000 Hz full-scale limit:

The best choice for this parameter depends upon the required
resolution, the number of digits in the totalizer, the extent of range
required, and the maximum counter input frequency.

NOTE

When totalizing on the LOI, the maximum total value is 1,000,000,000.

Auxiliary Output Control

In lieu of the pulse output on the digital terminals, an Auxiliary
Output Control is available to indicate a reverse flow or zero flow
condition. The two terminals are actually a transistor switch closure,
which must be externally powered.

Reverse Flow Enable

This choice activates the switch closure with a reverse flow. A forward
flow is defined by the flow direction arrow on the flowtube. This also
enables the totalizer to count in the reverse direction.

No Flow Enable

This choice activates the switch closure whenever the flow rate drops
below the low flow cutoff.

1000 gal/min

60 sec/min

0.01 gal/pulse

×

---------------------------------------------------------------------------

1666.65 Hz

=

HART Fast Keys

1, 4, 3, 2

LOI

Detailed Setup

«
...
52
53
54
55
56
...
»

Summary of Contents for 8732C































































































































Reviews:

No comments

Related manuals for 8732C

LevelMaster 7100

Brand: ABB Pages: 2

Brand: ABB Pages: 4

Brand: TA Pages: 58

Brand: Kawai Pages: 2

Brand: E+E Elektronik Pages: 40

Brand: NARDA Pages: 64

Brand: Radio Shack Pages: 44

Brand: Radiodetection Pages: 2

Brand: T&D Pages: 2

Brand: T&D Pages: 2

Professional Plus

Brand: YSI Pages: 28

Brand: RHS Pages: 8

Brand: Trotec Pages: 14

Brand: Vanguard Instruments Company Pages: 111

Brand: PCE Instruments Pages: 20

Brand: Hanna Instruments Pages: 2

Brand: Banner Pages: 4

Brand: Hanna Instruments Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands