Rosemount 8732C Manual Download Page 61 | Manualshive

Page: 61 / 126

background image

4-15

Transmitter Functions

TRANSMITTER
INFORMATION
CONFIGURATION

This function allows you to view and change identification data and
other information about the transmitter and flowtube. This information
does not affect the performance or operation of the transmitter; it is
strictly for information purposes (exceptions are noted below).

Transmitter Tag

Transmitter Tag is the quickest and shortest way of identifying and
distinguishing between transmitters. Transmitters can be tagged
according to the requirements of your application. The tag may be
up to eight characters long and is user-defined.

Software Revision Number

The Model 8732C microcontroller will automatically read the Software
Revision Number and display it under this heading. The software
revision number is not user-changeable.

Descriptor

Descriptor is a longer user-defined variable to assist with more
specific identification of the particular transmitter. It is usually used in
multi-transmitter environments and provides 16 characters.

Message

Message Variable provides an even longer user-defined variable
for identification and other purposes. It provides 32 characters of
information and is stored with the other configuration data.

Date

Date is a user-defined variable that provides a place to save the date of
the last revision of configuration information.

Flowtube Tag

Flowtube Tag is the quickest and shortest way of identifying and
distinguishing between Flowtubes. Flowtubes can be tagged according
to the requirements of your application. The tag may be up to eight
characters long and is user-defined.

Flowtube Serial Number

Flowtube Serial Number is stored in the transmitter configuration
for future reference. The number provides easy identification if the
flowtube needs servicing or for other purposes.

HART Fast Keys

1, 4, 5, 2

LOI

Device Information

HART Fast Keys

1, 4, 5

LOI

Device Information

HART Fast Keys

1, 4, 5, 3

LOI

Device Information

HART Fast Keys

1, 4, 5, 4

LOI

Device Information

HART Fast Keys

1, 4, 5, 5

LOI

Device Information

HART Fast Keys

1, 4, 5, 8

LOI

Device Information

HART Fast Keys

1, 4, 5, 7

LOI

Device Information

«
...
59
60
61
62
63
...
»

Summary of Contents for 8732C































































































































Reviews:

No comments

Related manuals for 8732C

Brand: Yamaha Pages: 83

Brand: Yamaha Pages: 63

Brand: dacell Pages: 22

NUFLO Scanner 2000 microEFM

Brand: Cameron Pages: 8

Brand: National Instruments Pages: 85

Brand: National Instruments Pages: 12

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 12

Brand: Parkside Pages: 94

Brand: Teledyne Hastings Instruments Pages: 54

Brand: Keeler Pages: 54

SoundTrack LxT N/Forcer

Brand: Larson Davis Pages: 12

Brand: Mark-10 Pages: 26

Brand: Fluke Calibration Pages: 13

Brand: Parker Pages: 16

Brand: Waterproof Pages: 51

Brand: JUMO Pages: 150

Brand: PASCO Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands