Rosemount 8732C Manual Download Page 105 | Manualshive

Page: 105 / 126

background image

A-9

Appendix A

MENUS AND FUNCTIONS

The HART Communicator is a menu driven system. Each screen
provides a menu of options that can be selected as outlined above,
or provides direction for input of data, warnings, messages, or
other instructions.

Main Menu

When the HART Communicator is turned on, one of two menus will
appear. If the HART Communicator is connected to an operating loop,
the communicator will find the device and display the Online Menu (see
below). If it is not connected to a loop, the communicator will indicate
that no device was found. When you press OK (F4), it will display the
Main Menu.

The Main Menu provides the following options:

• Offline–The Offline option provides access to offline configuration

data and simulation functions.

•

Online

–The Online option checks for a device and if it finds one,

brings up the Online Menu.

•

Transfer

–The Transfer option provides access to options for

transferring data either from the HART Communicator (Memory)
to the transmitter (Device) or vice versa. Transfer is used to move
off-line data from the HART Communicator to the flowmeter, or
to retrieve data from a flowmeter for off-line revision.

NOTE

Online communication with the flowmeter automatically loads the
current flowmeter data to the HART Communicator. Changes in on-line
data are made active by pressing SEND (F2). The transfer function is
used only for off-line data retrieval and sending.

•

Frequency Device

–The Frequency Device option displays the

frequency output and corresponding pressure output of current-
to-pressure transmitters.

•

Utility

–The Utility option provides access to the contrast control

for the HART Communicator LCD screen and to the autopoll
setting used in multidrop applications.

Once you have selected a Main Menu option, the HART Communicator
provides the information you need to complete the operation. If further
details are required, consult the HART Communicator manual.

Online Menu

The Online Menu can be selected from the Main Menu as outlined
above, or it may appear automatically if the HART Communicator is
connected to an active loop and can detect an operating flowmeter.

NOTE

The Main Menu can be accessed from the Online Menu. Press the left
arrow action key to deactivate the on-line communication with the
flowmeter and to activate the Main Menu options.

When configuration variables are reset in the on-line mode, the new
settings are not activated until the data are sent to the flowmeter.
Press SEND (F2) when it is activated to update the process variables of
the flowmeter.

On-line mode is used for direct evaluation of a particular meter, re-
configuration, changing parameters, maintenance, and other functions.

«
...
103
104
105
106
107
...
»

Summary of Contents for 8732C































































































































Reviews:

No comments

Related manuals for 8732C

Brand: Magnetic Instrumentation Pages: 63

Brand: Idexx Pages: 6

Brand: IDEAL INDUSTRIES Pages: 10

Brand: M-system Pages: 5

Brand: Velleman Pages: 16

Brand: Velleman Pages: 4

Brand: Velleman Pages: 8

Brand: velocomp Pages: 4

Brand: Yamaha Pages: 48

Brand: MULTISPAN Pages: 2

Brand: Stübbe Pages: 12

Brand: B meters Pages: 3

Brand: J-TECH Pages: 3

Brand: SV Pages: 88

Brand: Fluke Pages: 22

Brand: T Scale Pages: 64

Brand: INTERSPIRO Pages: 76

Brand: Net2Edge Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands