Rosemount 8732C Manual Download Page 86

Page: 86 / 126

Rosemount Model 8732C Integral Mount Magnetic Flowmeter System

7-6

(1) Consult factory for larger line sizes.
(2) When grounding rings (2 rings per meter) are specified, add 6.35 mm (0.25 in.) for 15 mm through 350 mm (½- through 14 in.) flowtubes or

12.7 mm (0.50 in.) for 400 mm (16 in.) and larger. When lining protectors are specified, add 6.35 mm (0.25 in.) for 15 mm through 300 mm
(½- through 12-in.) flowtubes, 12.7 mm (0.50 in.) for 350 mm through 900 mm (14- through 36-in.) flowtubes.

TABLE 7-4. Flowtube Dimensions with DIN Flanges in Millimeters (Inches).

Line Size

(1)

and Flange

Rating

Liner Face

Diameter

“A”

Process

Flange

Rad. “B”

Overall

Flowtube

Length

“L”

(2)

Body

Height

“C”

Body

Width “D”

with Port

Centerline

to Conduit

“E”

Bolt Hole

Circle

Diameter

Bolt Hole

Diameter

Number of

Bolts

15 mm PN 10–40

45 (1.77)

47 (1.87)

200 (7.88)

222 (8.75)

175 (6.88)

131 (5.16)

65 (2.56)

14 (0.55)

25 mm PN 10–40

68 (2.68)

58 (2.27)

200 (7.88)

222 (8.75)

186 (7.34)

131 (5.16)

85 (3.35)

14 (0.55)

40 mm PN 10–40

88 (3.46)

75 (2.96)

200 (7.87)

242 (9.52)

179 (7.05)

141 (5.57)

110 (4.33)

18 (0.71)

50 mm PN 10–40

102 (4.02)

83 (3.25)

200 (7.87)

242 (9.52)

190 (7.47)

141 (5.57)

125 (4.92)

18 (0.71)

80 mm PN 10–40

138 (5.43)

100 (3.94)

200 (7.87)

293 (11.52)

243 (9.57)

167 (6.57)

160 (6.30)

18 (0.71)

100 mm PN 10–16

158 (6.22)

110 (4.33)

250 (9.84)

310 (12.22)

254 (10.01)

176 (6.92)

180 (7.09)

18 (0.71)

100 mm PN 25–40

162 (6.38)

117 (4.63)

250 (9.84)

310 (12.22)

254 (10.01)

176 (6.92)

190 (7.48)

22 (0.87)

150 mm PN 10–16

212 (8.35)

142 (5.61)

300 (11.81)

366 (14.39)

264 (10.41)

204 (8.05)

240 (9.45)

22 (0.87)

150 mm PN 25

218 (8.58)

150 (5.91)

300 (11.81)

366 (14.39)

264 (10.41)

204 (8.05)

240 (9.45)

22 (0.87)

150 mm PN 40

218 (8.58)

150 (5.91)

332 (13.06)

366 (14.39)

264 (10.41)

204 (8.05)

240 (9.45)

22 (0.87)

200 mm PN 10

268 (10.55)

170 (6.70)

351 (13.81)

415 (16.33)

289 (13.38)

229 (9.02)

295 (11.61)

22 (0.87)

200 mm PN 16

268 (10.55)

170 (6.70)

351 (13.81)

415 (16.33)

289 (13.38)

229 (9.02)

295 (11.61)

22 (0.87)

200 mm PN 25

278 (10.94)

180 (7.09)

350 (13.78)

415 (16.33)

289 (13.38)

229 (9.02)

310 (12.20)

26 (1.02)

200 mm PN 40

285 (11.22)

187 (7.38)

396 (15.60)

415 (16.33)

289 (13.38)

229 (9.02)

320 (12.60)

30 (1.18)

250 mm PN 10

320 (12.60)

197 (7.70)

381 (15.00)

485 (19.11)

432 (17.00)

265 (10.44)

350 (13.78)

22 (0.87)

250 mm PN 16

320 (12.60)

202 (7.97)

381 (15.00)

485 (19.11)

432 (17.00)

265 (10.44)

355 (13.98)

26 (1.02)

250 mm PN 25

335 (13.19)

213 (8.39)

381 (15.00)

485 (19.11)

432 (17.00)

265 (10.44)

370 (14.67)

30 (1.18)

250 mm PN 40

345 (13.58)

225 (8.86)

435 (17.13)

485 (19.11)

432 (17.00)

265 (10.44)

385 (15.16)

33 (1.30)

300 mm PN 10

370 (14.57)

223 (8.76)

457 (18.00)

540 (21.27)

487 (19.16)

265 (10.44)

400 (15.75)

22 (0.87)

300 mm PN 16

378 (14.88)

230 (9.06)

457 (18.00)

540 (21.27)

487 (19.16)

293 (11.52)

410 (16.14)

26 (1.02)

300 mm PN 25

395 (15.55)

242 (9.55)

457 (18.00)

540 (21.27)

487 (19.16)

293 (11.52)

430 (16.93)

30 (1.18)

300 mm PN 40

410 (16.14)

258 (10.12)

512 (20.14)

540 (21.27)

487 (19.16)

293 (11.52)

450 (17.72)

33 (1.30)

350 mm PN 10

430 (16.93)

252 (9.94)

534 (21.03)

594 (23.39)

541 (21.28)

293 (11.52)

460 (18.11)

22 (0.87)

350 mm PN 16

438 (17.24)

260 (10.24)

534 (21.03)

594 (23.39)

541 (21.28)

320 (12.58)

470 (18.50)

26 (1.02)

350 mm PN 25

450 (17.72)

277 (10.93)

534 (21.03)

594 (23.39)

541 (21.28)

320 (12.58)

490 (19.29)

33 (1.30)

350 mm PN 40

465 (18.31)

290 (11.42)

591 (23.25)

594 (23.39)

541 (21.28)

320 (12.58)

510 (20.08)

36 (1.42)

400 mm PN 10

482 (18.98)

282 (11.12)

610 (24.00)

645 (25.04)

592 (23.30)

345 (13.59)

515 (20.28)

26 (1.02)

400 mm PN 16

490 (19.29)

290 (11.42)

610 (24.00)

645 (25.04)

592 (23.30)

345 (13.59)

525 (20.67)

30 (1.18)

400 mm PN 25

505 (19.88)

310 (12.21)

610 (24.00)

645 (25.04)

592 (23.30)

345 (13.59)

550 (21.65)

36 (1.42)

400 mm PN 40

535 (21.06)

330 (12.99)

667 (26.25)

645 (25.04)

592 (23.30)

345 (13.59)

585 (23.03)

39 (1.54)

450 mm PN 10

532 (20.94)

308 (12.13)

686 (27.00)

709 (27.93)

656 (25.82)

377 (14.85)

565 (22.24)

26 (1.02)

450 mm PN 16

550 (21.65)

320 (12.60)

686 (27.00)

709 (27.93)

656 (25.82)

377 (14.85)

585 (23.03)

30 (1.18)

450 mm PN 40

560 (22.05)

343 (13.50)

765 (30.12)

709 (27.93)

656 (25.82)

377 (14.85)

610 (24.02)

30 (1.18)

500 mm PN 10

585 (23.03)

335 (13.19)

762 (30.00)

761 (29.95)

707 (27.84)

403 (15.86)

620 (24.41)

26 (1.02)

500 mm PN 16

610 (24.02)

358 (14.08)

762 (30.00)

761 (29.95)

707 (27.84)

403 (15.86)

650 (25.59)

33 (1.30)

500 mm PN 25

615 (24.21)

365 (14.37)

762 (30.00)

761 (29.95)

707 (27.84)

403 (15.86)

660 (25.98)

36 (1.42)

500 mm PN 40

615 (24.21)

378 (14.88)

845 (33.25)

761 (29.95)

707 (27.84)

403 (15.86)

670 (26.38)

42 (1.65)

600 mm PN 10

685 (26.97)

390 (15.36)

914 (36.00)

885 (34.85)

823 (32.39)

461 (18.14)

725 (28.54)

30 (1.18)

600 mm PN 16

725 (28.54)

420 (16.54)

914 (36.00)

877 (34.51)

823 (32.39)

461 (18.14)

770 (30.31)

36 (1.42)

600 mm PN 25

720 (28.35)

423 (16.64)

914 (36.00)

877 (34.51)

823 (32.39)

461 (18.14)

770 (30.31)

39 (1.54)

600 mm PN 40

735 (18.94)

445 (17.52) 1,007 (39.64) 886 (34.88)

823 (32.39)

461 (18.14)

795 (31.30)

48 (1.88)

Summary of Contents for 8732C































































































































Search results

Summary of Contents for 8732C

Reviews:

Related manuals for 8732C

Brands by name

Popular brands

Rosemount 8732C, Manual

Search results

Summary of Contents for 8732C

Reviews:

Related manuals for 8732C

Brands by name

Popular brands