Roller CamView, Instruction Manual, Page: 12 / 56

2. Start-up
2.1. Handheld unit (5)
Remove the screw from the battery compartment (17) of the handheld unit (5)
(only in ROLLER’S CamView), push the cover in the direction of the arrow to
remove, remove the battery holder, insert 4 1.5 V, AA, LR6 batteries into the
battery holder, pay attention to the position of the plus-minus poles. Push the
battery holder back into the battery compartment, slide in the cover, screw in
the screw (only in ROLLER’S CamView). Always change all four batteries at
once.
2.2. Camera cable set Color (2)
Plug the camera cable set Color into the cable socket (3) of the handheld unit
(5). Position the strap of the camera cable set in line with the groove of the
handheld unit. Tighten the camera cable set hand-tight with the union nut of
the handheld unit.
The tools, add-on mirror, add-on hook, add-on magnet delivered with the camera
cable set Color 16-1 only fit the camera cable set Color 16-1 and are clipped
optionally to the camera head. Always close the flap otherwise the tool could
be lost.
The enclosed accessory set does not fit camera cable set Color 9-1. First push
the plastic sleeve over the wire of the tool of the add-on mirror, add-on hook
or add-on magnet. Hook the hook of the tool on the camera head into the hole
in the camera housing marked by an arrow. Align the plastic sleeve so that the
wire of the tool fits into the groove of the plastic sleeve. Push the plastic sleeve
up to the stop on the camera.
2.3. Controller unit (7) of ROLLER’S CamView and CamView S
WARNING
Caution: Mains voltage present! Before connecting the electrical device,
check whether the voltage given on the rating plate corresponds to the mains
voltage. On building sites, in a wet environment, indoors and outdoors or under
similar installation conditions, only operate the electrical device on the mains
with a fault current protected switch (FI breaker) which interrupts the power
supply as soon as the leakage current to earth exceeds 30 mA for 200 ms.
The controller unit (7) has an integrated Li-Ion battery. Change the controller
unit battery before start-up. Caution: Mains voltage present! To do so, connect
the power supply/charger to the mains/charger socket (16) of the controller and
a suitable wall socket. The battery charging time is approximately 3 hours. A
full charge lasts for about 2 hours of operation depending on the use. The
controller unit can also be operated with the power supply/Li-Ion charger.
Push the controller unit (7) onto the handheld unit (5) from above until it snaps
into place.
The controller unit (7) can be operated both by radio signal and directly with
the handheld unit (5). Transmission switches over to radio signal transmission
as soon as the controller unit is removed from the handheld unit.
2.3.1. Switching On the Endoscope Camera
The handheld unit (5) is switched on by turning the On/Off thumbwheel (4).
The Power-LED (6) lights. Switch on the controller unit (7) with the On/Off
button (8). Keep the On/Off button pressed for about 1 second. The brightness
of the LEDs on the colour camera can be adjusted by turning the On/Off
thumbwheel (4).
2.3.2. Inserting the MicroSD card
Insert the MicroSD-card in the MicroSD card slot (15). The tip of the arrow on
the MicroSD-card must point towards the display (19). The card snaps into
place. Press again to remove the MicroSD card.
Do not remove the MicroSD card or unplug the USB cable during photo/video
recording and data transfer to the PC because otherwise data will be lost and/
or the MicroSD card could be damaged.
MicroSD cards up to 32 GB can be used.
A MicroSD card is inserted
The MicroSD card is full
 No MicroSD card is inserted
eng eng
1.3. Handheld unit ROLLER’S CamView ROLLER’S CamView S ROLLER’S CamView Wi-Fi
Wi-Fi standard IEEE 802.11 b/g/n
Transmission frequency 2468 MHz 2468 MHz 2.4 GHz
Pixel image transfer 640 × 480
Modulation FM FM
Bandwidth 18 MHz 18 MHz
Wireless range up to 10 m up to 10 m up to 10 m
Power supply 4 batteries 1.5 V, AA, LR6 4 batteries 1.5 V, AA, LR6 4 batteries 1.5 V, AA, LR6
Dimensions 190 × 140 × 40 mm 190 × 165 × 53 mm 245 × 130 × 43 mm
Weight 260 g 320 g 250 g
1.4. Controller unit ROLLER’S CamView ROLLER’S CamView S ROLLER’S CamView Wi-Fi
Display 3.5” colour TFT-LCD 3.5” colour TFT-LCD see operating instructions
Pixels (display) 320 × 240 320 × 240 Smartphone/Tablet-PC
Pixels (recording) 640 × 480 640 × 480
Video system PAL / NTSC PAL / NTSC
Reception frequencies 2414, 2432, 2450, 2468 MHz 2414, 2432, 2450, 2468 MHz
Transmission channel not adjustable not adjustable
Battery integrated Li-Ion battery 3.7 V, 1.2 Ah integrated Li-Ion battery 3.7 V, 1.2 Ah
Power supply/charger 100 – 240 V AC, 50 – 60 Hz, input / 100 – 240 V AC, 50 – 60 Hz, input /
5 V DC, 1 A, output, protection class II DC 5 V / 1 A, output, protection class II
Video level 0.9 – 1.3 Vpp on 75 Ohm 0.9 – 1.3 Vpp on 75 Ohm
Video size 27 MB per minute 27 MB per minute
Frame rate up to 30 frames per second up to 30 frames per second
Zoom 1.5 / 2.0 / 2.5 / 3.0 × 1.5 / 2.0 / 3.0 ×
Dimensions 100 × 70 × 25 mm 105 × 90 × 42 mm
Weight 150 g 240 g
Temperature range –10°C ... +50°C / +14°F ... +122°F –10°C ... +50°C / +14°F – +122°F
Humidity 15 – 85% RH 15 – 85% RH
Tested units for see www.albert-roller.de under
ROLLER application software DOWNLOADS/Software/Compatibility
1.5. Camera cable set Color 16 mm camera 16 mm camera, 90° 9 mm camera 4.5 mm camera
Image sensor CMOS CMOS CMOS CMOS
Number of pixels 704 × 576 656 × 488 640 × 480 320 × 240
Viewing angle 50° 35° 36° 63°
Focus range 60 – 350 mm 35 – 80 mm 20 – 100 mm 10 – 50 mm
Min. lighting 0 Lux 0 Lux 0 Lux 0 Lux
Power supply by handheld unit by handheld unit by handheld unit by handheld unit
Dimensions Ø 16 × 970 mm Ø 16 × 970 mm Ø 9 × 970 mm Ø 4.5 × 1030 mm
Weight 280 g 185 g 190 g 30 g
Video format PAL PAL PAL NTSC
Type of protection camera IP 67 IP 67 IP 67 IP 67
≤ 30 min, ≤ 0.1 bar ≤ 30 min, ≤ 0.1 bar ≤ 30 min, ≤ 0.1 bar ≤ 30 min, ≤ 0.1 bar
12