Roland Fantom XR, Owner'S Manual

Page: 211 / 284

211
Effects List
63: STEP PCH SHIFTER
(STEP PITCH SHIFTER)
A pitch shifter in which the amount of pitch shift is varied by a 16-
step sequence.
fig.MFX-63
You can use multi-effect control to make the step sequence play
again from the beginning (p. 215).
64: REVERB
Adds reverberation to the sound, simulating an acoustic space.
fig.MFX-64
65: GATED REVERB
This is a special type of reverb in which the reverberant sound is cut
off before its natural length.
fig.MFX-65
66: OD
→
CHORUS
(OVERDRIVE
→
CHORUS)
fig.MFX-66
Parameter Range Explanation
Step 01–16 -24–+12 semi Amount of pitch shift at each
step (semitone units)
Rate # 0.05–10.00 Hz, note Rate at which the 16-step se-
quence will cycle
Attack # 0–127 Speed at which the amount of
pitch shift changes between steps
Gate Time # 0–127 Duration of the pitch shifted
sound at each step
Fine -100– +100 cent Pitch shift adjustment for all
steps (2-cent units)
Delay Time 0–1300 ms, note Delay time from the original
sound until the pitch-shifted
sound is heard
Feedback # -98– +98% Proportion of the pitch-shifted
sound that is to be returned to
the input (negative values in-
vert the phase)
Low Gain -15– +15 dB Amount of boost/cut for the
low-frequency range
High Gain -15– +15 dB Amount of boost/cut for the
high-frequency range
Balance # D100:0W–D0:100W Volume balance of the original
sound (D) and pitch-shifted
sound (W)
Level 0–127 Output volume
Parameter Value Description
Type ROOM1, ROOM2,
STAGE1, STAGE2,
HALL1, HALL2 Type of reverb
ROOM1: dense reverb with
short decay
ROOM2: sparse reverb with
short decay
STAGE1: reverb with greater
late reverberation
STAGE2: reverb with strong
early reflections
HALL1: reverb with clear re-
verberance
HALL2: reverb with rich re-
verberance
Pre Delay 0.0–100.0 ms Adjusts the delay time from the
direct sound until the reverb
sound is heard.
Time # 0–127 Time length of reverberation
L in
R in
Step Pitch Shifter
Step Pitch Shifter
L out
R out
2-Band
EQ
2-Band
EQ
L in
R in
L out
R out
Reverb
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
2-Band
EQ
HF Damp 200–8000 Hz,
BYPASS Adjusts the frequency above which
the reverberant sound will be cut.
As the frequency is set lower,
more of the high frequencies
will be cut, resulting in a softer
and more muted reverber-
ance. If you do not want to cut
the high frequencies, set this
parameter to BYPASS.
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Balance # D100:0W–D0:100W Volume balance between the direct
sound (D) and the reverb sound (W)
Level 0–127 Output Level
Parameter Value Description
Type NORMAL, REVERSE,
SWEEP1, SWEEP2 Type of reverb
NORMAL: conventional
gated reverb
REVERSE: backwards re-
verb
SWEEP1: the reverberant
sound moves from right to
left
SWEEP2: the reverberant
sound moves from left to
right
Pre Delay 0.0–100.0 ms Adjusts the delay time from the
direct sound until the reverb
sound is heard.
Gate Time 5–500 ms Adjusts the time from when the
reverb is heard until it disappears.
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Balance # D100:0W–D0:100W Volume balance between the
direct sound (D) and the reverb
sound (W)
Level # 0–127 Output Level
Parameter Value Description
Od Drive # 0–127 Degree of distortion
Also changes the volume.
Od Pan # L64–63R Stereo location of the overdrive
sound
Cho Pre Delay 0.0–100.0 ms Adjusts the delay time from the
direct sound until the chorus
sound is heard.
Cho Rate # 0.05–10.00 Hz, note Frequency of modulation
Cho Depth 0–127 Depth of modulation
Parameter Value Description
L in
R in
L out
R out
Gated Reverb
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
2-Band
EQ
L in
R in
Chorus
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Fantom-XR_r_e.book 211 ページ ２００６年４月４日 火曜日 午前１０時１４分