background image

Charter

9

3181

No.

Fig. 60

- Construct the fuselage nose assembly for the glow versi-

on from parts R16, R25, R26V and R27V, and glue the
joints soundly.

Fig. 61

- Glue the nose assembly to the fuselage.
- Glue the side fairings R22 and the nose fairing R23 in

place as shown. Relieve part R23 to follow the shape of
the former R26V.

- Sand the entire fuselage nose area to a neat, rounded

shape.

Fig. 62

- Press the four captive nuts V1 into the holes in the nose

bulkheads from the rear.

Fig. 63

- Fix the motor mount V2 in place using the screws V3.

Figs. 64 and 65

- Place the motor V4 on the mount, and mark a clearance

line for the silencer in the right-hand side and at the fuse-
lage nose. Cut away the cowl to clear the silencer.

- Cut the notch at the front for the throttle arm as shown.
- Place the motor on the mount arms again, mark the posi-

tion of the holes for the retaining screws using the motor
lugs as a guide, and drill them 3 mm Ø.

- Temporarily install the motor by fitting the screws V5

through the motor lugs and the mount arms.

- Mount the silencer on the motor, and check that there is

adequate clearance between it and the fuselage.

- Seal the opening in the front part of the fuselage with a

piece of cross-grained 1.5 mm balsa sheet V6.

Fig. 66

- Mark the position of the hole for the throttle linkage in the

nose bulkhead, in line with the throttle arm, and drill it 3.5
mm Ø.

- Cut the throttle snake outer V7 to a length of about 240

mm, fit it through the hole and glue it to the nose
bulkhead.

- Solder the threaded coupler V8 to the end of the throttle

pushrod, and screw the plastic clevis V9 on the end. Slip
the pushrod through the snake outer and connect the pla-
stic clevis to the throttle arm.

Fig. 67

- Press the rubber grommets and metal spacers into the

mounting lugs of the throttle servo V10, and install it in the
servo tray.

- Cut down the servo output arm as shown.
- Move the servo to the “full-throttle” position from the

transmitter, and open the carburettor barrel fully.

- Cut the pushrod to the correct length, solder the threaded

coupler V8 to the end and screw an M2 locknut on it.
Connect the pushrod to the servo using a clevis V11.

Figs. 68 and 69

- Install the two nipples in the fueltank V12 as described in

the instructions supplied with it.

- The tank is installed in the fuselage and packed round

with pieces of foam to hold it in position; note that the
foam has to be positioned before the tank is fitted.

- Cut overlength pieces of fuel tubing V13 (Fig. 70) and

connect them to the fueltank nipples. Stick a piece of
insulating tape to the fuel line which is connected to the
clunk pick-up.

- Remove the motor.

- We recommend that you seal the tank compartment

and the motor bay with sanding sealer or clear lacquer
to protect it from fuel.

- Place the fueltank in the fuselage, routing the fuel lines

through the large hole in the nose bulkhead.

- Cut a piece of 8 x 8 mm balsa strip V14 to length and

install it across the fuselage as shown, to hold the fuel-
tank in position. Tack the strip in place with just a few
drops of cyano so that you can remove it and withdraw
the fueltank at any time for maintenance.

Fig. 70

- Install the motor, and cut the fuel lines to the correct

length. When the motor has been installed permanently,
the fuel feed line (marked with tape) is connected to the
carburettor nipple.

- Remove the motor again. The motor should not be instal-

led permanently until the model has been covered.

Assembly and operating instructions

Stage 6 - tailplane and fin

Parts List for the tail panels

Part No.

Description

Material

Dimensions

No. off

L 1

Fin strake

Balsa

6 mm

Laser-cut

1

L 2

Fin

Balsa

6 mm

Laser-cut

1

L 3

Rudder

Balsa

6 mm

Laser-cut

1

L 4

Tailplane centre section

Balsa

8 mm

Laser-cut

1

L 5

Elevator

Balsa

8 mm

Laser-cut

1

L 6

Tailplane cross-piece

Balsa

8 x 3 mm

As plan

12

L 7

Leading edge / trailing edge

Balsa

8 x 8 mm

As plan

5

L 8

Gusset

Poplar ply

3 mm

Laser-cut

2

L 9

Hinge

Nylon

-

Ready made

8

L10

Hinge peg (tooth-pick),

N.I.

Beech

2 mm Ø

8

Summary of Contents for Charter 3183

















































Reviews: