Ricoh SP 8200DN Technical Bulletin Download Page 20

Page: 20 / 79

echnical

ulletin

PAGE: 1/2

Reissued: 09-Oct-09

Model:

Al-P1

Date:

23-May-08

No.:

RG179010b

RTB Reissue

The items in

bold italics

have been corrected or added.

Installation Procedure for the IPDS Option

When Used on the Model AL-P1

The IPDS option will be released in June 2008. The installation procedure for this option
on the Model AL-P1 is shown below.

IPDS OPTION

Accessories
Description Q’ty

1. IPDS Emulation SD Card ...................................................... 1

Important:

Only one Slot 1 is available for SD cards that contain applications. If you want

to use more than one application, merge all applications into one SD card
(SP5873-001).

Installation

1. Make sure the following requirements have been met.

Requirements:

The Hard Disk Drive Option Type 5000 must be installed.

The following firmware versions must be installed:

Firmware Name

Version

Firmware Number

System

V1.08 or later

G1795740B

NCS

V7.14 or later

G1795742B

Websys

V1.12 or later

G1795743B

Printer

V1.08 or later

G1795746B

2. Turn OFF the main switch.

Subject:

IPDS Option Release

Prepared

by:

K. Hamada

From:

2nd Tech Support Sec. Service Support Dept.

Classification:

Troubleshooting
Mechanical
Paper path

Part information
Electrical
Transmit/receive

Action required
Service manual revision
Retrofit information

Product Safety

Other ( )

Tier 2

Summary of Contents for SP 8200DN
















































































Search results

Summary of Contents for SP 8200DN

Reviews:

Related manuals for SP 8200DN

Brands by name

Popular brands

Ricoh SP 8200DN, Technical Bulletin

Search results

Summary of Contents for SP 8200DN

Reviews:

Related manuals for SP 8200DN

Brands by name

Popular brands