Ricoh SP 8200DN Technical Bulletin Download Page 63

Page: 63 / 79

echnical

ulletin

PAGE: 1/2

Model:

AL-C2

Date:

05-Mar-14

No.:

RD129048

Subject:

Part Catalog Correction

Prepared by:

M.Yoneda

From:

2nd Tech Service Sect., MFP/P Tech Service Dept.

Classification:

Troubleshooting

Mechanical

Paper path

Product Safety

Part information

Electrical

Transmit/receive

Other (

)

Action required

Service manual revision

Retrofit information

Tier 2

Old part

number

New part

number

Description

Q’ty Int

Page

Index Note

-D0092617

D1292617

GUIDEPLATE:REGISTRATION:UPPER

0-1

X/O

Change:

The method for attaching the COVER-PAPER DUST REMOVAL &

GUIDPLATE:REGISTRATION:UPPER was changed.

See details below.

Reason:

To further strengthen the integrity of the connection.

Current method:

The guide plate is fixed by mounting the ends of the shaft and fixing it in place with spring pressure.

Summary of Contents for SP 8200DN
















































































Search results

Summary of Contents for SP 8200DN

Reviews:

Related manuals for SP 8200DN

Brands by name

Popular brands

Ricoh SP 8200DN, Technical Bulletin

Search results

Summary of Contents for SP 8200DN

Reviews:

Related manuals for SP 8200DN

Brands by name

Popular brands