Ricoh SP 8200DN Technical Bulletin Download Page 51

Page: 51 / 79

echnical

ulletin

PAGE: 1/1

Model: AL-P1

Date:

20-Apr-11

No.:

RG179021

Subject:

Parts information

Prepared by:

T.Hirakawa

From:

1st Overseas Tech Support Sec., 1st PQM Dept.

Classification:

Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Product Safety

Other (

)

Tier 2

Change:

Some circuit elements on the PCB (PSU) were changed.

Reason:

To improve reliability.

Old parts

number

New parts

number

Description Q’ty

Int Page

Index

AZ240141

AZ240191

POWER SUPPLY UNIT -230V

1/1

O/O

105 21

Target model codes:

AL-C1.5(EU): D029-92

AL-C1.5(AA): D091-29, D092-29

AL-C1.5 (CHN) - D091-21, D092-21

AL-C1(EU): D012-92, D013-92

AL-C1 (AA): D009-29, D011-29, D012-29, D013-29

AL-C1 (CHN): D009-21, D009-61, D012-21, D012-61

AL-C1 (KRE) - D009-28, D011-28, D012-28, D013-28

AL-P1 (EU): G179-22, G179-27

Summary of Contents for SP 8200DN
















































































Search results

Summary of Contents for SP 8200DN

Reviews:

Related manuals for SP 8200DN

Brands by name

Popular brands

Ricoh SP 8200DN, Technical Bulletin

Search results

Summary of Contents for SP 8200DN

Reviews:

Related manuals for SP 8200DN

Brands by name

Popular brands