Ricoh SP 8200DN Technical Bulletin Download Page 22

Page: 22 / 79

echnical

ulletin

PAGE: 1/1

Model:

Model Al-P1

Date:

3-Jun-08

No.:

RG179011

Subject:

SC866(SD card error 1)

Prepared

by:

K. Hamada

From:

2nd Tech Support Sec. Service Support Dept.

Classification:

Troubleshooting
Mechanical
Paper path

Part information
Electrical
Transmit/receive

Action required
Service manual revision
Retrofit information

Product Safety

Other ( )

Tier 2

SYMPTOM

SC866 (SD Card Error 1: Confirmation) occurs when installing an SD card option if the
System firmware is older than Ver1.08.

CAUSE

Due to a firmware bug (System), the machine cannot authenticate the SD card.

Note:

There is nothing wrong with the SD card or application itself. The problem is with

the System/Copy firmware.

SOLUTION

If you want to install an SD card option, update the System firmware to

Ver1.08

(G1795740B)

or later before you install the option.

SD Card Options

The symptom may occur when you install any of the following options on machines that
contain System firmware older than Ver1.08.

Option Name

Code

IPDS Unit Type 5100

M345-05

VM Card Type G

M345-13/19/20

SD Card for Fonts Type B

M345-24

Summary of Contents for SP 8200DN
















































































Search results

Summary of Contents for SP 8200DN

Reviews:

Related manuals for SP 8200DN

Brands by name

Popular brands

Ricoh SP 8200DN, Technical Bulletin

Search results

Summary of Contents for SP 8200DN

Reviews:

Related manuals for SP 8200DN

Brands by name

Popular brands