Ricoh SP 8200DN Technical Bulletin Download Page 38

Page: 38 / 79

PAGE: 13/14

Appendix

Matrix of Available Installation/Activation Tools

Installation
Destination

Action WIM

Remote

Manager

SD Card

Installation Yes

Yes

Activation No Yes

Version Up

Yes

CAP

Target

Machine

Activation -

Installation No

CAP-ES Server

Activation No

Installation Yes

Yes

Activation No Yes

Version Up

Yes

ELP-NX
APP

Target

Machine

Activation No Yes

Installation Yes

Activation -

Version Up

Yes

ELP-NX
Filter

Target

Machine

Activation -

CAP: Card Authentication Package Embedded Type

CAP-ES: Card Authentication Package Server Type

ELP-NX APP: Enhanced Locked Print - NX Application

ELP-NX Filter: Enhanced Locked Print - NX Filter

WIM:

Web

Image

Monitor

-: Not necessary

Installation File Types

SD Card

Unzipped folder of each application

Remote Manager

Zip file of each application

Web Image Monitor

All applications except ELP-NX Filter: Zip file (same as RM)

ELP-NX Filter: Unzipped folder in the /sdk/webinstaller folder.

Summary of Contents for SP 8200DN
















































































Search results

Summary of Contents for SP 8200DN

Reviews:

Related manuals for SP 8200DN

Brands by name

Popular brands

Ricoh SP 8200DN, Technical Bulletin

Search results

Summary of Contents for SP 8200DN

Reviews:

Related manuals for SP 8200DN

Brands by name

Popular brands