Error Code
(Hex)
Symptom
Probable Cause
Solution
A1
Front cover opened. (The front
open switch is not pressed
down.)
Hook of the front open
switch on the front cover
broken
Replace the front cover.
Front open switch broken
Replace the front open
switch.
Main PCB defective
Replace the main PCB.
A2
Document length exceeding
the scan limitation.
During scanning, 90 cm or
longer of a document is
detected.
During document feeding or
ejecting, 400 cm or longer of
a document is detected.
Document jam
Remove the jammed
document.
Actuator R caught on the
surrounding parts
Reassemble the actuator R.
Document rear sensor
broken
Replace the panel PCB
ASSY.
Main PCB defective
Replace the main PCB.
A3
The document rear sensor
does not come ON during
document pull-in operation.
Document jam
Remove the jammed
document.
Actuator R caught on the
surrounding parts
Reassemble the actuator R.
Scanning motor F sub
ASSY defective
Replace the scanning motor
F sub ASSY.
Document rear sensor
broken
Replace the panel PCB
ASSY.
Panel PCB ASSY
defective
A4
Not used.
-
-
A5
FAX scanning failure.
(1st time) (Data scanning
error)
Data scanning is failed.
Turn the machine ON, then
OFF. Retry scanning.
Error Indication
31
2
Summary of Contents for HL-F1
