Ricoh 403079 - Aficio SP C410DN-KP Color Laser Printer Hardware Manual Download Page 4

Page: 4 / 204

Positions of

WARNING and

CAUTION

labels

This machine has labels for

WARNING and

CAUTION at the positions

shown below. For safety, please follow the instructions and handle the machine
as indicated.

High temperature parts. Turn off the main power and be careful when replacing
fusing unit/removing misfed paper.

The inside of this printer becomes very hot. Do not touch parts labelled “

” (in-

dicating a hot surface). Touching these parts will result in burns.

AQC0

Summary of Contents for 403079 - Aficio SP C410DN-KP Color Laser Printer












































































































































































































Search results

Summary of Contents for 403079 - Aficio SP C410DN-KP Color Laser Printer

Reviews:

Related manuals for 403079 - Aficio SP C410DN-KP Color Laser Printer

Brands by name

Popular brands

Ricoh 403079 - Aficio SP C410DN-KP Color Laser Printer, Hardware Manual

Search results

Summary of Contents for 403079 - Aficio SP C410DN-KP Color Laser Printer

Reviews:

Related manuals for 403079 - Aficio SP C410DN-KP Color Laser Printer

Brands by name

Popular brands