Ricoh 403079 - Aficio SP C410DN-KP Color Laser Printer Hardware Manual Download Page 27

Page: 27 / 204

Attaching Paper Feed Unit Type 4000

Lift the printer using the inset grips on both sides of the printer.

Important

❒

The printer should always be lifted by at least two people.

Align the printer with the two upright pins on the paper feed unit and then
lower the printer slowly.

When installing two paper feed units, connect the two units first using the
same procedure below before connecting the units to the printer.

AQC031S

AET074S

AET075S

Summary of Contents for 403079 - Aficio SP C410DN-KP Color Laser Printer












































































































































































































Search results

Summary of Contents for 403079 - Aficio SP C410DN-KP Color Laser Printer

Reviews:

Related manuals for 403079 - Aficio SP C410DN-KP Color Laser Printer

Brands by name

Popular brands

Ricoh 403079 - Aficio SP C410DN-KP Color Laser Printer, Hardware Manual

Search results

Summary of Contents for 403079 - Aficio SP C410DN-KP Color Laser Printer

Reviews:

Related manuals for 403079 - Aficio SP C410DN-KP Color Laser Printer

Brands by name

Popular brands