Ricoh 403079 - Aficio SP C410DN-KP Color Laser Printer Hardware Manual Download Page 23

Page: 23 / 204

Available Options

Installing Options

Install options in the positions shown in the illustration.

❖

Exterior

Paper Feed Unit Type 4000

Loads up to 550 sheets of paper.
Up to two paper feed units, can be in-
stalled on the printer. Installed tray
units are identified as “Tray 2” and
“Tray 3”.
See p.14 “Attaching Paper Feed Unit
Type 4000”.

AET061S

Summary of Contents for 403079 - Aficio SP C410DN-KP Color Laser Printer












































































































































































































Search results

Summary of Contents for 403079 - Aficio SP C410DN-KP Color Laser Printer

Reviews:

Related manuals for 403079 - Aficio SP C410DN-KP Color Laser Printer

Brands by name

Popular brands

Ricoh 403079 - Aficio SP C410DN-KP Color Laser Printer, Hardware Manual

Search results

Summary of Contents for 403079 - Aficio SP C410DN-KP Color Laser Printer

Reviews:

Related manuals for 403079 - Aficio SP C410DN-KP Color Laser Printer

Brands by name

Popular brands