30
4.9.5
Menu 9: Setting other operating modes
1.
To choose between menu “9” options
.
ð
After approximately 2 seconds, the display flashes and shows the set value of the operating mode.
The factory setting is "0".
2. If desired, adjust the setting with the aid of the OPEN (B
⬆
) and CLOSE (C
⬇
) buttons.
Value
Description
Note
0
Normal operation
Factory settings
1
Normal operation with
ventilation settings*
Allows the ventilation of the garage. In this mode, the garage door is approximately 10 cm wide open.
To start up the ventilation setting, press the second button on the transmitter that must be programmed in menu 2.
The garage door can be closed at any time using the radio transmitter.
The garage door closes automatically after 60 minutes.
2
Partial opening of sliding
sideways sectional door*
In this mode, the garage door is approximately 1 m wide open.
To start up the partial opening, press the second button on the transmitter that must be programmed in menu 2.
5
OPEN-CLOSE operation
Giving a pulse command with door in CLOSE position, the drive starts and the door moves up to the total OPEN position.
Giving a pulse command during opening has no effect and the door continues to open.
Giving a pulse command with door in OPEN position, the door closes.
Giving a pulse command during closing, the door stops and opens again.
6
Automatic closing
("AR")**
A pulse command always causes the opening of the door.
After the auto-close time and pre-flashing time (menu A) the door closes automatically.
An interruption of the photobeams infrared ray during closing causes 2s pause and reverse direction.
An interruption of the photobeam during opening has no effect.
7
Automatic closing
("AR")**
Function as in point 6, however, an interruption of the photobeam during opening causes early stop of the movement and the auto-close time starts.
8
Automatic closing
("AR")**
Function as in point 7, however, a pulse command gived during opening causes early stop of the movement and the auto-close time starts.
9
Automatic closing
("AR")**
Function as in point 8, but without auto-close.
Remarks:
• *: The second button of the transmitter must be reprogrammed after changes in operating modes 1 or 2.
• **: A paio of photobeams must be installed.
3. Press the programming button (PROG button) (D).
ð
With 0, 1, 2 or 5 option value, "H" menu options are displayed. Continue with
Menu "H".
ð
With 6, 7, 8 or 9 option value, "A" menu options are displayed. Continue with
Menu "A".
WARNING
Impact and crush hazard due to automatic door movement!
Make sure that no persons stand in the movement area of the door because it may start unexpectedly.
4.9.6
Menu A: Set auto close waiting time TCA
Visible only if enabled one of the "Automatic close" options of Menu “9”.
1.
To choose between menu “A” options
ð
After approximately 2 seconds, the display flashes and shows the set Value of Auto close waiting time (TCA).
2. If desired, adjust the setting with the aid of the OPEN (B
⬆
) and CLOSE (C
⬇
) buttons.
Value TCA - Auto close waiting time
0
0 s
1
10 s
2
30 s
Value TCA - Auto close waiting time
3
60 s
4
90 s
5
120 s
Value TCA - Auto close waiting time
6
150 s
7
180 s
8
210 s
Value TCA - Auto close waiting time
9
240 s
3. Press the programming button (PROG button) (D)
ð
The Menu "H" is displayed.
4.9.7
Menu H: STOP-A settings
1.
To choose between menu “H” options
ð
After approximately 2 seconds, the display flashes and shows the set value of the operating mode.
The factory setting is "0".
2. If desired, adjust the setting with the aid of the OPEN (B
⬆
) and CLOSE (C
⬇
) buttons.
Value
Remarks
0
Safety strip (with 8k2 resistor) connected to STOP-A input (terminal G)
1
Jumper or NC switch connected to STOP-A input (terminal G)
3. Press the programming button (PROG button) (D)
ð
The display shows "0". End of menu (if necessary, continue with forces learning cycle).
4.10
Completing the installation procedure
Close the cover of the drive head.
Check if the garage door operates properly and safely. See chapter "Maintenance / Checks".
4.11
Attaching the warning sticker
Place the sticker clearly visible on the inner surface of the garage door.
G
B
