RHINO FN120 Operator'S Manual Download Page 50 | Manualshive

Page: 50 / 224

background image

12

Prepare For Safe Operation

Hitching Mower To Tractor

Three-point hitch-mounted mowers:

— Refer to mower and tractor manufacturers’ manuals.
— Place tractor’s hydraulic power lift (rockshaft)

selector lever in down position to avoid unexpected
movement.

— Explain the hitching procedures to those operators

who cannot read.

— Front-end weights may be needed to maintain

steering control and front-end stability. Refer to the
manufacturers' operator's manual(s).

— When backing the tractor up to the mower, NEVER

allow anyone between the tractor and the mower.

— Attach the mower to the tractor three-point links and

securely pin in position.

— Securely attach the driveline to the tractor PTO.

Lower the master shield into place if it is movable.
Push and pull on the driveline to ensure it is locked
onto the PTO shaft.

Read and

Understand

Manuals Before

Operating

Maintain

Proper Weight

Distribution

No One

Allowed Between

Tractor and

Mower

Avoid

Entanglement,

Use Guards and

Shields

Pull-type hitch-mounted mowers:

— Refer to mower and tractor manufacturers’ manuals.
— Remove three-point hitch quick coupler if equipped.
— Attach only to drawbar hitch.
— Adjust tractor drawbar length for 540 or 1000 rpm

PTO operation.

— When backing the tractor up to the mower, NEVER

allow anyone between the tractor and the mower.

— Properly attach the mower safety tow chain to the

tractor.

— Securely attach the driveline to the tractor PTO. Push

and pull on the driveline to ensure it is locked onto
the PTO. Lower the master shield into place.

— Hook up the mower hydraulic hoses to the tractor.
— Make sure the wings, or raised mower decks, are

supported by the cylinders before removing the
transport locks. Never use force to release the
transport or wing locks. The wings or deck could fall
and crush you.

Conﬁ rm Wings Are

Supported Before

Releasing Locks

Avoid

Entanglement,

Use Guards and

Shields

Prepare For Safe Operation

Tractor

Drawbar

Adjustment

14IN

540 RPO PTO

1-3/8" 6 SPLINE

1000 RPO PTO

1-3/8" 21 SPLINE

16IN

1000 RPO PTO

1-3/4" 20 SPLINE

20IN

540 RPM PTO
1-3/8" 6 SPLINE

1000 RPM PTO
1-3/8" 21 SPLINE

1000 RPM PTO
1-3/4" 20 SPLINE

«
...
48
49
50
51
52
...
»

Summary of Contents for FN120

































































































































































































































Reviews:

No comments

Related manuals for FN120

Brand: ECLOZ Pages: 60

Brand: Sears Pages: 37

Brand: Toro Pages: 32

Derby Stallion ZT2561

Brand: Simplicity Pages: 39

RANSOMES 933304J

Brand: Textron Pages: 28

Brand: Parkside Pages: 392

HS-7030 HITCH-N-SWEEP

Brand: Parker Pages: 6

Brand: Jacobsen Pages: 106

Brand: MTD Pages: 20

Brand: Stanley Pages: 26

Brand: Ozito Pages: 14

Brand: Black+Decker Pages: 12

Brand: Cub Cadet Pages: 8

Brand: Cub Cadet Pages: 20

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 64

Brand: Craftsman Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands