RHINO FN120 Operator'S Manual Download Page 115 | Manualshive

Page: 115 / 224

background image

OPERATION

FN180/FN120 07/12

Operation Section 4-9

© 2012 Alamo Group Inc.

OPERA

T

ION

5.1 Connecting the Mower Tongue to the Tractor

1.

Ensure the tractor is equipped with the
correct PTO shaft and the drawbar is set at
the correct length.

2.

Using the parking jack, position the tongue
clevis to the height of the tractor drawbar.
Adjust the mower tongue to be level and
parallel with the tractor drawbar using the
control rod connecting the mower tongue to
the deck.

3.

Board the tractor and start the engine. Back
the tractor to the mower aligning the drawbar
hitch hole with the mower tongue clevis.
Turn off the tractor engine, place the tractor
in park, and set the parking brake before
dismounting.

5. CONNECTING THE MOWER TO THE TRACTOR

Use extreme caution when connecting the mower to the tractor. The mower should be securely resting at
ground level or setting on blocks. Keep hands and feet from under the mower deck and clear of pinch points
between the tractor hitch arms and mower pins.

OPS-R-0001

Always shut the Tractor completely down, place the transmission in park, and set the
parking brake before you or anyone else attempts to connect or disconnect the Implement
and Tractor hitches.

(S3PT-15)

«
...
113
114
115
116
117
...
»

Summary of Contents for FN120

































































































































































































































Reviews:

No comments

Related manuals for FN120

Brand: Land Pride Pages: 60

Brand: H&S Pages: 32

MULTICLIP MULTICLIP 46 S SVAN

Brand: Stiga Pages: 2

Brand: Jacobsen Pages: 36

Brand: Murray Pages: 52

Brand: Ransomes Pages: 81

Brand: Toro Pages: 16

Brand: Land Pride Pages: 2

Brand: Snapper Pages: 32

Brand: Yard Pro Pages: 100

26" Leaf/Lawnsweeper 45-02181

Brand: Agri-Fab Pages: 12

Brand: Land Pride Pages: 48

Mowers DIESEL 1500cc

Brand: Bad Boy Pages: 54

Brand: VonHaus Pages: 20

Brand: Land Pride Pages: 58

Brand: Dolmar Pages: 76

Brand: Troy-Bilt Pages: 40

Brand: Land Pride Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands