RHINO FN120 Operator'S Manual Download Page 108 | Manualshive

Page: 108 / 224

background image

OPERATION

FN180/FN120 07/12

Operation Section 4-2

© 2012 Alamo Group Inc.

OPERA

T

ION

RHINO FN180/FN120 NITRO ROTARY MOWER

OPERATION INSTRUCTIONS

Rhino FN180/FN120 NITRO rotary mowers are manufactured with quality material by skilled workers. These
mowers are designed to cut grass, weeds, crop stalks, brush and other vegetation up to 5” diameter. The
mower is equipped with protective deflectors and/or chain guards to prevent objects being thrown from the
mower by the blades, however, no shielding is 100% effective. All shields, guards, deflectors, and chains
equipped on the unit must be maintained on the mower in good operational condition.

It is the operator’s responsibility to be knowledgeable of all potential operating hazards and to take every
reasonable precaution to ensure oneself, others, animals, and property are not injured or damaged by the
mower, tractor, or a thrown object. Do not operate the mower if passersby, pets, livestock, or property are
within 300 feet of the unit.

This section of the Operator’s Manual is designed to familiarize, instruct, and educate safe and proper mower
use to the operator. Pictures contained in this section are intended to be used as a visual aid to assist in
explaining the operation of a flex-wing rotary mower and are not necessarily of a FN180/FN120 NITRO cutter.
Some pictures may show shields removed for picture clarity. NEVER OPERATE this implement without all
shields in place and in good operational condition. The operator must be familiar with the mower and tractor
operation and all associated safety practices before operating the mower and tractor. Proper operation of the
mower, as detailed in this manual, will help ensure years of safe and satisfactory use of the mower.

IMPORTANT:

To avoid mower damage, retorque all bolts after the first 10 hours of operation. Retighten blade

carrier retaining nut on gearbox lower shafts to 600 ft. lbs.

READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS
MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND
IMPLEMENT.

If you do not understand any of the instructions, contact your nearest authorized dealer for a

full explanation. Pay close attention to all safety signs and safety messages contained in this manual and
those affixed to the implement and tractor.

OPS-U- 0001

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or
death may occur unless care is taken to follow the warnings and instructions stated in the
Safety Messages. Always use good common sense to avoid hazards.

(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las
medidas de seguridad.

(SG-3)

«
...
106
107
108
109
110
...
»

Summary of Contents for FN120

































































































































































































































Reviews:

No comments

Related manuals for FN120

Brand: EarthWise Pages: 9

Brand: Cub Cadet Commercial Pages: 32

Brand: ZIPPER MASCHINEN Pages: 65

Brand: Yard-Man Pages: 5

Brand: FGM Pages: 33

Brand: Yardworks Pages: 36

Brand: Toro Pages: 52

Brand: Toro Pages: 60

LMO 18-36 Battery

Brand: Kärcher Pages: 252

Brand: Nac Pages: 24

Brand: Murray Pages: 18

Brand: Black & Decker Pages: 4

Brand: Black & Decker Pages: 8

Brand: Black & Decker Pages: 9

Brand: Black & Decker Pages: 8

Brand: Black & Decker Pages: 164

Brand: Black & Decker Pages: 2

Brand: Craftsman Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands