RHINO FN120 Operator'S Manual Download Page 103 | Manualshive

Page: 103 / 224

background image

ASSEMBLY

FN180/FN120 07/12

Assembly Section 3-7

© 2012 Alamo Group Inc.

ASSEMBL

Y

2.

Inner center axle dual tire assemblies are shipped bolted on wing mount tubes. Remove transport bars
from wings and lower each wing so that inner tire and hub assembly can be removed and installed on
center axle.

NOTE: It will be necessary to raise each side of center axle slightly so inner dual tires can be

installed.

3.

Install gearbox vents or vent dipsticks if not installed.Check all gearbox lube levels.

TIRES AND WHEELS

Before installing any tires and wheels make certain the Cutter is jacked up high enough and is securely

supported. When installing laminated or airplane tires, be sure the flat side of the lug nut is against the wheel.

There are only three types of tires that can be used on this cutter DO NOT USE ANY OTHER TYPE OF TIRE

OR WHEEL, such as automotive tires and rims. DO NOT EXCEED THE MAXIMUM SPEED FOR EACH TYPE

OF TIRE. As excessive speed can cause damage to the machine, tire, and wheel.

When installing Laminated Tires and Wheels note the direction of travel and the curvature of rubber segments

in the tire and install as shown in

Figure

Asm-R-0127

. Do not exceed 20 M.P.H. on Laminated Tires. When

removing Airplane Tires, let all of the air out of the tire before removing lug nuts or wheel bolts or nuts. Remove

valve core to make certain that there is no air pressure left in tube before separating wheel halves to dismount

tires. DO NOT LOOSEN WHEEL CLAMP BOLTS BEFORE PRESSURE IS REMOVED FROM TUBE AND

TIRE TO PREVENT EXPLOSIVE SEPERATION OF WHEEL HALVES WITH POSSIBLE SERIOUS BODILY

INJURY. Do not exceed 20 M.P.H. on Airplane or Rib Implement Tires.

Maximum airplane tire inflation pressure is 50 PSI, minimum inflation pressure is 20 PSI. Inflate ribbed

implement tires to manufacturer rated PSI as shown on the tire sidewall.

«
...
101
102
103
104
105
...
»

Summary of Contents for FN120

































































































































































































































Reviews:

No comments

Related manuals for FN120

Brand: Baroness Pages: 5

Brand: Yard Machines Pages: 12

Brand: Simplicity Pages: 32

Brand: Nakayama Pages: 14

Brand: TOPMAQ Pages: 20

135 B TITAN DOD

Brand: Stiga Pages: 100

Brand: Spearhead Pages: 32

Brand: Exmark Pages: 4

Brand: Husqvarna Pages: 52

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 104

Brand: Husqvarna Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands