RHINO FN120 Operator'S Manual Download Page 177

Page: 177 / 224

MAINTENANCE

FN180/FN120 07/12

Maintenance Section 5-21

MAINTENANCE

Blade Bolt Inspection

Inspect Blade Bolt Head daily for wear as followed:

Inspect the Blade Bolt Heads daily for abnormal wear. REPLACE BOTH BLADE BOLTS on
the Blades IMMEDIATELY if either blade bolts has:

•

Visible cracks or

•

If the recessed area on blade bolt is worn off or

•

If Blade Bolt has gouges or chipped areas.

Failure to replace abnormally worn blade bolts may lead to catastrophic failure of the blades and ejection of the
broken part which may cause serious bodily injury or death.

Always replace Blade Bolts with new bolts whenever replacing the Blades.

Summary of Contents for FN120

































































































































































































































Search results

Summary of Contents for FN120

Reviews:

Related manuals for FN120

Brands by name

Popular brands

RHINO FN120, Operator'S Manual

Search results

Summary of Contents for FN120

Reviews:

Related manuals for FN120

Brands by name

Popular brands