RGB Spectrum Linx DVI User Manual Download Page 39

Page: 39 / 64

C O M M A N D S

Commands Summary

350-8794 V1.1

Linx DVI 8x8 Matix Switcher User’s Guide

. . . . .

COMMAND

. . . . . . . . .

ARGUMENTS

Required parameter values are shown in angle brackets

< >

and

optional parameters are contained in square brackets

[ ]

COMMAND <value1> [value2]

In this example,

is a required parameter and

[value2]

is an

optional parameter.

PREDEFINED

PARAMETER

. . . . . . . . .

VALUES

Some commands have predefined values, and only these may be
entered as arguments. Predefined parameter values are indicated as:

<value1|value2|value3>

Example:

The choices for

BAUDrate

are:

<1200|2400|9600|19200|38400|57600|115200>

QUERY THE

. . . . . . . . .

CURRENT SETTING

Many commands will report back on the current parameter settings. To
establish the current parameters associated with the command enter the
command without any arguments.

Linx Switcher

will respond with the

current settings of the selected parameter.

Example:

To display the current IP address of the

Linx

Switcher

, enter the

IPADDRess

command without entering an

argument.

Typing the command:

IPADDR

might return:

192.168.1.201

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C O M M A N D S S U M M A R Y

Note

Do not use the delete key when entering commands.
The backspace key may be used.

Table 4-1

Alphabetical List of Commands

Command

Type

Description

BAUDrate

Communication

Sets the baud rate for the serial port.

DELeteEDID

EDID

Deletes the EDID parameters from the EDID list.

DELetePreSeT

Switch

Deletes specific preset or all presets.

DISPLAYMODE

EDID

Sets the display ID reported for dynamic EDID mode.

ECHO

Communication

Turns the serial echo on/off.

EDIDMode

EDID

Sets EDID mode to fixed or dynamic.

Summary of Contents for Linx DVI

































































Search results

Summary of Contents for Linx DVI

Reviews:

Related manuals for Linx DVI

Brands by name

Popular brands

RGB Spectrum Linx DVI, User Manual

Search results

Summary of Contents for Linx DVI

Reviews:

Related manuals for Linx DVI

Brands by name

Popular brands