RGB Spectrum Linx DVI User Manual Download Page 24

Page: 24 / 64

O P E R A T I O N

Command Line Operation

350-8794 V1.1

Linx DVI 8x8 Matix Switcher User’s Guide

. . . . .

. . . . . . . . .

EDID

EDID commands are used to set the display resolution and timing to be
used by the graphics host. See

EDID Control

for an explanation of

EDID management.

EDIDMode

- Set the EDID mode to fixed or dynamic.

DISPLAYMODE

- Set the display EDID mode to emulated or pass-

through.

EDIDPRiority

- Select minimum resolution or output number as priority

criteria.

LoaDFixedEDID

- Load EDID list entry into input fixed EDID register.

LoaDEmulateEDID

- Load EDID list entry to the output emulate register.

SaVeEDID

- Save content of the display register to an EDID list entry.

DELeteEDID

- Delete an EDID list entry.

NAMEEDID

-Name an EDID list entry.

LiStEDID

- List the parameters for one or more EDID list entries.

EXportEDID

- Exports an EDID list entry to memory for FTP transfer.

IMportEDID

- Imports an EDID list entry after FTP transfer.

EXPORTING AND

IMPORTING SYSTEM

. . . . . . . . .

SETTINGS

System settings can be exported to a text file and transferred to a PC for
subsequent import back to a

Linx Switcher

. It is recommended that

settings be exported prior to updating firmware. Exporting and importing
can also be used to transfer settings between multiple switchers. See

Transferring Files

on page 44 for instructions on transferring exported

files to and from the

Linx Switcher

EXPORTSETTINGS

- The exported parameters can be selected by

entering the appropriate argument to the command. These are presets,
system, EDID, or all.

P R E S E T S

The name assigned for all 99 presets is listed. This is followed by the
output 1 and its input number for all presets; subsequent outputs and
input routes for all presets follows.

S Y S T E M

The model number and firmware version are saved to a file.

Summary of Contents for Linx DVI

































































Search results

Summary of Contents for Linx DVI

Reviews:

Related manuals for Linx DVI

Brands by name

Popular brands

RGB Spectrum Linx DVI, User Manual

Search results

Summary of Contents for Linx DVI

Reviews:

Related manuals for Linx DVI

Brands by name

Popular brands