manualshive.com logo in svg

Resource Data Management DMTouch, Commissioning & Service Manual

Share
Download
Resource Data Management DMTouch Commissioning & Service Manual Download Page 51

 

www.resourcedm.com 

  

Revision 2.3 

Page 51 of 72 

Commissioning & Service Guide DMTouch 

 

 

Warning 

 
 
 
 
 
 

Please Note 

The specifications of the product detailed on this 
Set-Up  Guide  may  change  without  notice.  RDM 
Ltd. shall not be liable for errors or for incidental 
or consequential damages, directly and indirectly, 
in connection with the furnishing, performance or 
misuse of this product or document.

 

Ensure that all power is 
switched off before   
installing or maintaining 
this product 

www.resourcedm.com 

Trim control can be achieved in two ways either by Humidity or Dewpoint 
control. Humidity control is outlined below followed by Dewpoint control. 
 
On Humidity Control, the screen will display the values of; 

 

Humidity 

 

Trim Level 

 

Trim Power (used power / full power) 

 
Also shown are the various options required to configure the Trim Control. 
Depending on the method chosen will dictate the available options. 
 
To set up the Humidity based control alter the following settings; 
 

No Probe Time

: 

Probe fault delay time (in minutes). 

GP Channel

: 

Allows a GP channel to set the trims to a pre-determined 
level (normally Site opening times). 

GP Off Level

: 

Trim level when the above GP channel is off. 

rH Source

: 

Map this to the controller that has the humidity sensor. 

Humidity (%rH)

: 

Minimum and maximum levels (see graph below). 

Trim %:

   

Minimum and maximum trim power (see graph below). 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
If the relative humidity (rH) is below its low setting, the trims will be at their 
low setting. If the rH is above its high setting, the trims will be at their high 
setting. 
Between the low and high rH settings the relationship between the rH and 
Trim level is linear, as per the graph opposite. 
If the sensor fails, the trims will operate above 

the “Trims High” value 

 
Data Manager Network Trim control, when enabled, over-rides the controller

’s 

local trim level setting. 
 
The trims can be mapped to a GP timer, for example Site trading hours. By 
setting the GP Timer Off percentage determines the trim output level when 
the GP Timer is ‘Off’. This allows the user to further limit the power of the trim 
heaters or it can completely disable the heaters when the Site is not trading. 
Note setting GP channel to 0 will disable this feature. 
 

Note

: If the humidity sensor fails the alarm “Trim no probe” is generated by 

the System. 
 

Humidity Based Trim Control 
 
Trim Control 

 

 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 

 
 
 
 
 

 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Move to the bottom of the page and you will find the device list 
 
On viewing this menu the user can select which cases to apply trim 
control.  
 
The user can select an individual case, a group of cases or all of the 
cases displayed to be configured for trim control. 
 
By pressing enable on a case the user can turn trim control on and 
enter the power of each case trim heater in KW. 
 
Once configured press ‘Set Values’ 

Summary of Contents for DMTouch









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands