REMEHA Gas 120 ACE - 115 User Manual Download

Page: 35 / 96

Tab.9

If operating on propane

Type of boiler

Action

Gas 120 ACE - 65

Rotate the setting screw A on the venturi 6½ turns in a clockwise direction

Gas 120 ACE - 90

Rotate the setting screw A on the venturi 6½ turns in a clockwise direction

Replace the current gas valve unit with the propane gas valve unit according to the instruc

tions supplied with the propane conversion kit

Gas 120 ACE - 115

Rotate the setting screw A in a clockwise direction until it is closed, then:

Rotate the setting screw A on the gas valve unit 3½–4 turns in an anticlockwise direction

1. Set the fan speed as indicated in the table (if necessary). The setting

can be changed with a parameter setting.

Tab.10 Factory settings G20 (H gas)

Code

Parameter

Description

Adjustment range

Gas

120

ACE -

Gas

120

ACE -

Gas

120

ACE -

115

DP003

Abs. max fan DHW

Maximum fan speed on Domestic

Hot Water

1000 Rpm 7000 Rpm

5600

6300

6800

GP007

Fan RPM Max CH

Maximum fan speed during Central

Heating mode

1400 Rpm 7000 Rpm

5600

6300

6800

GP008

Fan RPM Min

Minimum fan speed during Central

H Domestic Hot Water

mode

1400 Rpm 4000 Rpm

1600

1750

GP009

Fan RPM Start

Fan speed at appliance start

1000 Rpm 4000 Rpm

2500

Tab.11 Setting for gas type G30/G31 (butane/propane)

Code

Parameter

Description

Adjustment range

Gas

120

ACE -

Gas

120

ACE -

Gas

120

ACE -

115

DP003

Abs. max fan DHW

Maximum fan speed on Domestic

Hot Water

1000 Rpm 7000 Rpm

5300

5800

6500

GP007

Fan RPM Max CH

Maximum fan speed during Central

Heating mode

1400 Rpm 7000 Rpm

5300

5800

6500

GP008

Fan RPM Min

Minimum fan speed during Central

H Domestic Hot Water

mode

1400 Rpm 4000 Rpm

1600

1800

GP009

Fan RPM Start

Fan speed at appliance start

1000 Rpm 4000 Rpm

2500

Tab.12 Setting for gas type G31 (propane)

Code

Parameter

Description

Adjustment range

Gas

120

ACE -

Gas

120

ACE -

Gas

120

ACE -

115

DP003

Abs. max fan DHW

Maximum fan speed on Domestic

Hot Water

1000 Rpm 7000 Rpm

5400

6000

6700

GP007

Fan RPM Max CH

Maximum fan speed during Central

Heating mode

1400 Rpm 7000 Rpm

5400

6000

6700

GP008

Fan RPM Min

Minimum fan speed during Central

H Domestic Hot Water

mode

1400 Rpm 4000 Rpm

1600

2000

1800

GP009

Fan RPM Start

Fan speed at appliance start

1000 Rpm 4000 Rpm

2500

3500

2. Check the setting of the gas/air ratio.

7 Commissioning

7717201 - v03 - 25062019

MID _HMI T-control - Gas 120 ACE

Summary of Contents for Gas 120 ACE - 115

































































































Search results

Summary of Contents for Gas 120 ACE - 115

Reviews:

Related manuals for Gas 120 ACE - 115

Brands by name

Popular brands

REMEHA Gas 120 ACE - 115, User Manual

Search results

Summary of Contents for Gas 120 ACE - 115

Reviews:

Related manuals for Gas 120 ACE - 115

Brands by name

Popular brands