103
Starting Generator
The following generator starting information is
specified for use at the ship’s main control panel
located in the cabin.
It also assumes that the
checklist on the last page has been completed
and all system components are in good running
condition.
For further information, contact your
closest Regal dealer, refer to the generator operation
manual and/or the illustration of the ship’s panel.
1. Turn “on” the generator sea cock in the engine
room.
2. Check the ship’s main control panel to ensure
shore main and all equipment breakers are
deactivated.
3. At the ship’s main control panel activate the
generator blower. Let it run for at least 4 minutes
before starting the generator.
4. Activate the toggled “start” switch and hold. This
will engage the generator starter to crank over the
gen-set engine.
5. Once the generator starts, release the “start”
switch.
6. Let the generator run without a load for several
minutes.
7. At the ship’s main control panel slide the starboard
parallel (transfer) bar up.. Activate the breaker.
8. Push the port bar up. Activate the generator
breaker.
At this point AC voltage should display on the AC
line voltage meter.
9. Activate the desired AC equipment breakers.
Stopping Generator
To stop the generator follow these steps at the ship’s
main control panel;
1. Turn to the “off” position all AC equipment
breakers.
2. Turn to the “off” position the 50 amp AC generator
breaker. At this point, no AC line voltage will be
displayed at the AC volt meter. Let the generator
run for 3-5 minutes without a load to cool down.
3. Stop the generator by activating the “stop” switch
on the panel. Hold switch until generator stops.
Summary of Contents for 38 SAV 2019
