background image

7

87 mm

21 mm

Diagram 4

If you are replacing an earlier model of the
Redring Selectronic you will need to remove
the appropriate backplate section subject to
whether the mains water plumbing approach
is either top or bottom entry. See Diagram 2 
- Options 

‘A’

 or 

‘B’

.

For surface mounted Top entry for plumbing 
remove and discard section 

‘C’

 and for the 

Bottom entry option do likewise with section

 

‘D’

.

Make sure the backplate is square on the wall 
and tighten the retaining screws which hold it 
to the wall.

Turn ON the mains water supply and check for 
leaks in the pipework connection to the 
shower.

Note:

 At this stage no water can flow through 

the unit.

IMPORTANT:

 Using a suitable sealant, 

always seal around the incoming pipework 
through the wall to prevent water entering 
the wall.

WARNING! 

The outlet of the shower 

acts as a vent and MUST NOT be 
connected to anything other than the 
Hose and Showerhead supplied or 
approved by the manufacturer

Electrical Connections

The electrical installation must be in accord-
ance with the current BS7671 (I.E.T. wiring 
regulations) and “Part P” of the Building 
Regulations and/or local regulations.

The unit is designed for a single phase 50 Hz 
a.c. electrical supply.

Please check the rating plate on the unit to 
see what details apply to your unit.

A means for disconnection in all poles 

must 

be 

incorporated in the fixed wiring in accord

-

ance with the wiring rules. 

We recommend 

ceiling switches.

The cable size required is determined by the 
kW rating of the shower and the distance 
between the shower and the consumer unit. 
The table on Page 8 is for 

guidance only

 in 

choosing the correct cable for your installation.

I

If on installation it is the intention to use YT2 
conduit trunking to conceal the surface 
electrical cable to either the Top or Bottom 

TRIAC

COOLER

FLOW 

TRANSDUCER

INLET

THERMISTOR

STEPPER

MOTOR

L

E

N

SOLENOID

TRIAC PCB

UMBILICAL

STEP

FLOW

TRIAC

IN

OUT

TEMPS

POWER

OUTLET

THERMISTOR

HEA

T EXCHANGER

Wiring Diagram

Summary of Contents for Selectronic Premier

























Reviews: