background image

17

5.

 A stabiliser is built into the flow 

    valve to automatically compensate 
    for small fluctuations in water 
    pressure that frequently occur in 
    households.

    There are three further controls to 
    cater for exceptional reductions in 
    water pressure to prevent the 
    shower from getting too hot.

    a) If the flow of water is less than 
        1.0 l/min the power to the 
        elements is switched off, but the
        solenoid valve remains open 
        allowing water to flow through 
        the shower.

    b) If the outlet temperature sensor 
        senses an excessive 
        temperature the flow of water 
        and the heating elements will 
        automatically switch off. The 
        electronics will signal over 
        Temperature condition (see 
        “over temperature shutdown” 
        section).

    c) A two stage mechanical thermal 
        cut-out is mounted on the top of 
        the heat exchanger independent 
        of the electronics.
 
        Stage one switches the power 
        off to the elements if it senses 
        an excessive temperature.
        The switch operates with an 
        audible click and will reset if 
        cold water is run through the
        shower.

        Stage two only operates if an 
        extreme temperature is sensed.
        The cut out will permanently 
        switch off and it will then have 
        to be replaced.

 Manufacturer

Glen Dimplex

 Product

RSELP85S
RSELP85P

RSELP85WPC

RSELP95S
RSELP95P

RSELP95WPC

RSELP108S
RSELP108P

 Load profile

XS

XS

XS

 Efficiency Class

A

A

A

 Efficiency %

37

37

37

 Consumption
 (kWh \ annum)

495

488

489

 Thermostat
 Setting (°C)

40

40

40

 Sound (dB)

15

15

15

 Precautions

Follow all product installation, care and maintenance 

instructions as listed in this “instruction / installation” 

manual

This information shows how our products pass the relevant european union energy 

directives (ErP).

 

ENERGY RELATED PRODUCT DIRECTIVE (ErP)

ENSURE POWER IS OFF BEFORE REMOVING COVER.

REPLACE THIS COVER PRIOR T

O FITTING THE FRONT COVER.

W

ARNING

WARNING
THIS

PRODUCT
MUST BE
EARTHED

TERMINAL

BLOCK

TEMPLOCK

SWITCH

SOLENOID

VALVE

INLET

COVER

POWER

PCB

BRASS

COOLER

MOTOR

FLOW

TRANSDUCER

FLOW

VALVE

OUTLET

TEMP

SENSOR

OUTLET

HEAT

EXCHANGER

LOGIC

PCB

DIP 

SWITCH

THERMAL

CUTOUT

Summary of Contents for Selectronic Premier

























Reviews: