Raymarine STV60 Installation & Operation Instructions Download Page 44

Page: 44 / 82

Raymarine Satellite TV Antenna Systems

Setting the DiSEqC Method

DiSEqC selection can be made from ACU. However, this

mode is not recommended for novice satellite service users.

1. Press YES to enter setup mode.

2. Press NEXT five times to enter DIS-

EQC mode.

3. Press YES to use DISEQC.

4. Select the

DiSEqC Method*

PREV - Shows previous DiSEqC Method.

SELECT/ENTER - Set the displayed DiSEqC

method.

NEXT - Shows next DiSEqC Method.

Press ENTER to move to next screen.

SETUP MODE ?

SET SAT PAIR ?

USE DISEQC ?

DO NOT USE DISEQC

YES

SELECT

5. Press YES to accept the selection.

Press NO to cancel and return to main

setup mode.

SAVE ?

YES

DiSEqC Method*

DO NOT USE DISEQC - DiSEqC is not being used.

USE TO CHANGE BAND - DiSEqC is being used to change to low and high band.

USE TO CHANGE SAT - DiSEqC is being used to change tracking satellite.

Summary of Contents for STV60



















































































Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands

Raymarine STV60, Installation & Operation Instructions

Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands