Raymarine STV60 Installation & Operation Instructions Download Page 40

Page: 40 / 82

Raymarine Satellite TV Antenna Systems

Setting the Antenna Parameters

It is not recommended for a novice satellite service user

to use this mode. Consult Technical Support for changing

antenna parameters.

1. Press YES to enter setup mode.

2. Press NEXT three times to enter set

antenna parameter menu.

4. Select the

PARAM*

PREV - Shows previous parameter.

SELECT - Set the displayed parameter.

NEXT - Shows next parameter.

Press ENTER to move to next screen.

SETUP MODE ?

SET SAT PAIR ?

PARAM: SCAN OFFSET

YES

5. Input the WRS LEVEL.

+ increases the value. - decreases the

value.

Change the underscored digit using

the +/- buttons.

Press INPUT to accept the value and

move to next digit.

Press BACK to move to previous digit.

Press ENTER to move to next screen.

6. Press YES to setup another parameter.

Press NO to cancel and return to main

setup mode.

7. Press YES to save the input informa-

tion.

Press NO to cancel and return to main

setup mode.

WRS LEVEL : 0500

ANOTHER PARAMETER

SAVE ?

YES

INPUT

3. Press YES to set antenna parameter.

SET ANT PARAMETER

YES

Summary of Contents for STV60



















































































Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands

Raymarine STV60, Installation & Operation Instructions

Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands