Raymarine STV60 Installation & Operation Instructions Download Page 16

Page: 16 / 82

Raymarine Satellite TV Antenna Systems

Installation and Mounting of Antenna

The method of installing and mounting the antenna may

vary due to vessel design, but the following procedures are

applicable in most situations, and will result in a secure and

effective installation.

Confirmation of Size Prior to Installation

• Confirm the height and diameter of the bottom surface of

the antenna before installing.

• The space must be sufficient for installing the antenna unit

considering the height and diameter of the antenna.

• The height and the diameter of the bottom surface of the

antenna are as shown in the following drawing. If possible,

install the antenna using a “power tower”.

Note:

Before installing the antenna open the radome and

remove the shipping constraints from the antenna interior.

Reinstall the radome before operating the system. The

system will not perform properly if the radome is open.

Figure 08: Radome Dimension of STV60

Ø70 cm (27.5”)

72 cm (28.3”)

Summary of Contents for STV60



















































































Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands

Raymarine STV60, Installation & Operation Instructions

Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands