Raymarine STV60 Installation & Operation Instructions Download Page 74

Page: 74 / 82

Raymarine Satellite TV Antenna Systems

7. GUI

This view shows a graphical representation of the current

antenna position which allows you to easily identify whether

or not the antenna is aligned properly to the target satellite

or is in a block zone. In addition, this view shows the current

satellite that the antenna is pointed towards and the satellites

that are located at a 180°arc on the horizon, according to the

current position.

8. Work View Functions

The 7 Work View Tabs displayed in the Work View can be

arranged in customized layouts.

Layout Formatting

• Each of the Work View Tab can be separated from the rest

of the Tabs.

Click and hold the left mouse button on the Work View Tab’s

header and then drag a desired Tab out. When a Work View

Tab is separated from the rest of your Work View Tabs, again

click and hold the left mouse button on the Work View Tab’s

header to display a cross-shaped Navigator icon. While

holding the mouse button, bring the selected Work View Tab

closer to the Navigator icon and release the mouse button

at your desired position (top, left, right or bottom arrow). This

time, the selected Tab will be moved to the desired position.

Note:

Based on the satellite EIRP footprint and the size of the

antenna, you may not be able to track all the satellites visible

in 180° arc.

Move the selected Work View Tab

to the top position of the Work View

layout.

Summary of Contents for STV60



















































































Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands

Raymarine STV60, Installation & Operation Instructions

Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands