Raymarine STV60 Installation & Operation Instructions Download Page 71

Page: 71 / 82

Tracking

: not used on STV series.

Rate Sensor Bias

: not used on STV series.

Tilt Sensor Bias

: not used on STV series.

Show Param

: shows the current antenna parameters.

Check NID

: verifies the NID (network ID) of the current

tracking transponder. Press the NID button to obtain the NID

only if the antenna is locked onto the desired satellite.

Start Debug

: starts the debug log of the antenna. The

debug message will be displayed once the debug button is

pressed.

Stop Debug

: stops debug logging of the antenna.

Save Debug (Start/Stop)

: starts or stops saving the debug

log. This button is enabled once the Start Debug button is

pressed.

Clear View

: clears the debug message or log data in

monitoring window.

5. Monitor

This view provides a user interface which can monitor all

data that has been received from the ACU.

Summary of Contents for STV60



















































































Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands

Raymarine STV60, Installation & Operation Instructions

Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands