Raymarine STV60 Installation & Operation Instructions Download Page 31

Page: 31 / 82

Normal Mode

Start Up

With the system installed and power applied, the ACU screen

will show the following sequence:

1. Data communication is being

established between the antenna and

the ACU. The ACU is initialized.

2. The antenna is initialized.

3. The antenna is searching for Satellite A.

4. The antenna has located the satellite

and is now tracking.

INITIALIZE ACU

INITIALIZE ANTENNA

SEARCH A: DTV101

TRACKING A: DTV101

B:DTV119 SETUP

Changing Target Satellite

Your antenna is pre-programmed with either 2 (Dual-Sat

mode) or 3 (Tri-Sat mode) candidates of target satellites as

a default mode. To change a target satellite, press LEFT

soft key. The target satellite is changed and is automatically

tracked by the antenna.

Default Dual-Sat Mode

1. Press LEFT soft key for tracking

Satellite B.

2. The antenna is tracking Satellite B.

TRACKING A: DTV101

TRACKING B: DTV119

B: DTV119 SETUP

A: DTV101 SETUP

Summary of Contents for STV60



















































































Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands

Raymarine STV60, Installation & Operation Instructions

Search results

Summary of Contents for STV60

Reviews:

Related manuals for STV60

Brands by name

Popular brands