Raymarine STV60 Installation & Operation Instructions Download Page 63 | Manualshive

Page: 63 / 82

background image

63

System Property Status Dashboard

The property status dashboard on the left pane of the screen allows the antenna status, the availability of TX transmission, signal

level, GPS status, software information, product information and error status to be monitored quickly.

1

2

3

Antenna Status:

Displays the status of the current mode of the antenna.

- Search: Antenna is searching the selected satellite.
- Tracking: Antenna is tracking the target satellite.
- Initialize: Antenna or ACU is initializing.
- Setup: Antenna is in SETUP mode.
- Sleep: Antenna is in Sleep mode.
- Unwrap: Antenna is unwinding/winding the cable in the antenna.

Tracking Satellite

Display or set current tracking satellite and tracking information. Up to 3 satellites can be

selected.

Signal Level

The “Red” line indicates the signal “Detect Level Threshold” and the “Orange” line indicates

the signal “Tracking Level Threshold”. If the signal level is higher than the tracking level

threshold, the signal level bar will display “Blue” color. If the signal level is lower than the

tracking level threshold, the signal level bar will display “Orange” color and the antenna will

stay in searching mode.

Note:

If the signal level is not higher than the tracking threshold, decrease the detect

and tracking level.

«
...
61
62
63
64
65
...
»

Summary of Contents for STV60



















































































Reviews:

No comments

Related manuals for STV60

Brand: MALA Pages: 16

Brand: Williams Sound Pages: 4

IPGUARD MD-ANT345G

Brand: NACD Pages: 5

Traveller-Man 3

Brand: Megasat Pages: 68

33691 ultra-flat digital amplified antenna

Brand: GE Pages: 10

Brand: GE Pages: 8

Brand: GE Pages: 4

Brand: GE Pages: 16

Brand: GE Pages: 12

Brand: GE Pages: 8

Ultra Pro Hover HD 250

Brand: GE Pages: 5

Brand: GE Pages: 5

Brand: GE Pages: 2

Brand: GE Pages: 10

Brand: GE Pages: 32

Brand: GE Pages: 36

Brand: RADIOHAUS Pages: 10

Brand: urmet domus Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands