manualshive.com logo in svg

R&S CMW-KG4 Series, User Manual, Page: 383 / 988

Share
Download
R&S CMW-KG4 Series User Manual Download Page 383

WCDMA Signaling

R&S

®

CMW-KG4xx/-KM4xx/-KS4xx

383

User Manual 1173.9657.02 ─ 11

CONFigure:WCDMa:SIGN<i>:UL:PRACh:PREamble:SUBChannels

<SubChannels>

Specifies which of the 12 PRACH subchannels are available. The information is coded
in a 12-bit number where the bits from left to right indicate the availability of subchan-
nel 11 to subchannel 0 (0=not available, 1=available).

The default format is decimal, but you can also enter binary numbers
(#B000000000000 to #B111111111111).

Parameters:

<SubChannels>

Range: 

#B000000000000  to  #B111111111111

*RST: 

#B000000000001

Example: 

See 

Configuring Physical Channel UL Settings

Firmware/Software: 

V1.0.15.0

Options: 

R&S CMW-KS410

Manual operation:

See 

"Preamble Subchannels"

 

on page 171

CONFigure:WCDMa:SIGN<i>:UL:PRACh:PREamble:MRETrans 

<Retransmission>

Sets the maximum number of preambles to be transmitted before a single preamble
cycle is terminated.

Parameters:

<Retransmission>

Range: 

1  to  64

*RST: 

6

Example: 

See 

Configuring Physical Channel UL Settings

Firmware/Software: 

V1.0.15.0

Options: 

R&S CMW-KS410

Manual operation:

See 

"Preamble Maximum Retransmission"

 

on page 171

CONFigure:WCDMa:SIGN<i>:UL:PRACh:PREamble:AICH 

<Preambles>

Specifies the number of preambles to be received before the instrument transmits the
AICH.

Parameters:

<Preambles>

Range: 

1  to  6

*RST: 

1

Example: 

See 

Configuring Physical Channel UL Settings

Firmware/Software: 

V3.0.20

Options: 

R&S CMW-KS410

Manual operation:

See 

"Preambles before AICH Transmission"

 

on page 172

Command Reference

深圳德标仪器 

135-1095-0799

Summary of Contents for CMW-KG4 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments