manualshive.com logo in svg

R&S CMW-KG4 Series, User Manual, Page: 245 / 988

Share
Download
R&S CMW-KG4 Series User Manual Download Page 245

WCDMA Signaling

R&S

®

CMW-KG4xx/-KM4xx/-KS4xx

245

User Manual 1173.9657.02 ─ 11

The "Config" hotkey opens either the configuration dialog of the measurement or the
configuration dialog of the signaling application, depending on which softkey is cur-
rently active.

Fig. 2-121: HSDPA ACK tab

Results

For a detailed description of the results see 

chapter 2.2.19.2, "Measurement Results"

,

on page 75.

Remote command: 

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

TRACe:

​

THRoughput:

​

CARRier<c>:

​

CURRent?

​

 etc.

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

TRACe:

​

THRoughput:

​

CARRier<c>:

​

AVERage?

​

 etc.

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

TRACe:

​

THRoughput:

​

TOTal:

​

CURRent?

​

 etc.

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

TRACe:

​

THRoughput:

​

TOTal:

​

AVERage?

​

 etc.

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

TRACe:

​

MCQI:

​

CARRier<c>:

​

CURRent?

​

 etc.

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

THRoughput:

​

CARRier<c>:

​

ABSolute?

​

 etc.

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

THRoughput:

​

CARRier<c>:

​

RELative?

​

 etc.

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

TRANsmission:

​

CARRier<c>?

​

 etc.

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

BLER:

​

CARRier<c>?

​

 etc.

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

MSFRames?

​

 etc.

FETCh:

​

WCDMa:

​

SIGN<i>:

​

HACK:

​

MCQI:

​

CARRier<c>?

​

 etc.

Related hotkeys

To display the hotkeys press the "Display" softkey. The following hotkeys are then
available at the bottom of the GUI:

GUI Reference

深圳德标仪器 

135-1095-0799

Summary of Contents for CMW-KG4 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments