Raisecom iTN8600-I Product Description Download

Page: 28 / 71

Raisecom
iTN8600-I (A) Product Description

3 Cards and parts

Raisecom Proprietary and Confidential

3.1.5 LEDs

Table 3-4 lists LEDs on the iTN8600-I.

Table 3-4

LEDs on the iTN8600-I

Print

Color

Description

SYS

Green

System working LED



Green: the system works abnormally.



Off: the system works abnormally.



Blinking green: the system works normally.

ALM

Red

Alarm LED



Red: severe alarms are generated on the device.



Blinking: minor alarms are generated on the device.



Off: no alarm is generated on the device.

LNK/ACT

Green

SNMP/EXT interface working LED



Green: the interface is properly connected.



Off: the interface is not connected or improperly
connected.



Blinking green: the interface is sending/receiving data.

C1–C16,
C19, C22

Red

Client-side interface alarm LED



Red: LOS alarms are generated.



Off: no LOS alarm is generated.

LOS

Red

Line-side interface alarm LED



Red: LOS alarms are generated.



Off: no LOS alarm is generated.

3.2 DC power supply RPD1304-48S12

3.2.1 Version

Table 3-5

Version of the DC power supply

Model

Version

RPD1304-48S12

A.00 or later

3.2.2 Appearance

Figure 3-2 shows the panel of the DC power supply, including the captive screw, heat
dissipation holes, handle, power LED, and power interface.

Summary of Contents for iTN8600-I








































































Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands

Raisecom iTN8600-I, Product Description

Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands