Raisecom iTN8600-I Product Description Download | Manualshive

Page: 19 / 71

background image

Raisecom
iTN8600-I (A) Product Description

1 Overview

Raisecom Proprietary and Confidential

Copyright © Raisecom Technology Co., Ltd.

9

When only one power supply is used, install a black panel over the position of the
other power supply. The black panel has the following functions:



Prevent human body from touching circuit boards inside the chassis, thus
avoiding danger.



Prevent dusty or foreign matter from entering the chassis.



Keep the chassis meeting requirements for EMC and electrostatic shielding.



Keep correct direction of cooling air flow inside the chassis.

Cables



The configuration cable and power cable are delivered with the iTN8600-I, and they can
be additionally purchased.



The power cable depends on the actual situation of the target area. When you order the
iTN8600-I, specify one power cable. You can also purchase multiple power cables.



For the DC power model, only the 3-pin connector, rather than the DC power cable, is
delivered, so you need to make the DC power cable according to the regional standard
and Table 5-19 by connecting the 3-pin connector with the DC power cable, as shown in
Figure 5-10.

Table 1-4

Ordering information about purchased cables

Model

Description

CBL-USB-USB-AM/USB-AM-
1.5m/RoHS

Configuration cable, used on the Console interface

POL-AC-European 3-
pin/receptacle-AC power cable-
0.75mm2-1.5m /RoHS

European AC power cable, used for the AC power
supply

POL-AC-American 3-
pin/receptacle-AC power cable-
18AWG-1.5m/RoHS

American AC power cable, used for the AC power
supply

POL-DC-unstripped/stripped-DC
power cable-1.0mm2-4m/RoHS

DC power cable, used for the DC power supply, used
with the 5.08-3Pin-header/RoHS connector.

Optical modules

Optical modules are used according to actual situations, so purchase them additionally.

For Raisecom optical modules and lookup table, see section 5.1 Lookup table of optical
module . For detailed parameters, see the corresponding user manual.

«
...
17
18
19
20
21
...
»

Summary of Contents for iTN8600-I








































































Reviews:

No comments

Related manuals for iTN8600-I

Brand: DAPAudio Pages: 28

Brand: Navman Pages: 16

Brand: Furuno Pages: 2

Brand: Raymarine Pages: 76

Brand: JRC Pages: 4

Brand: Furuno Pages: 3

Brand: LoopTone Pages: 5

Brand: Hitachi Pages: 23

Brand: Hitachi Pages: 28

Brand: Hitachi Pages: 13

Brand: Baofeng Pages: 56

Brand: AvaLAN Pages: 9

Brand: Siemens Pages: 7

Brand: Siemens Pages: 2

SIMATIC RTLS4060T

Brand: Siemens Pages: 13

Brand: Siemens Pages: 4

Brand: Siemens Pages: 6

SIMATIC 6GT2700-6DE03

Brand: Siemens Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands