Raisecom iTN8600-I Product Description Download

Page: 29 / 71

Raisecom
iTN8600-I (A) Product Description

3 Cards and parts

Raisecom Proprietary and Confidential

Figure 3-2

Panel of the DC power supply

PWR

-48V

RTN

3.2.3 Functions

Table 3-6

Functions of the DC power supply

Function

Description

Basic functions



Support wide voltage input range of -40 to -57 VDC.



Support the maximum load of 175 W.

Protection
functions



Support dual power supply 1+1 protection.



Support dual power load balancing.



Support how swapping.

3.2.4 Interface

Table 3-7

Interface on the DC power supply

Print

Type

Description

–

3-pin Phoenix
connector



Used with the 5.08-3Pin-header/RoHS connector



-48V: connected to the negative terminal



RTN: connected to the positive terminal

3.2.5 LED

Table 3-8

LED on the DC power supply

Print

Color

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

Summary of Contents for iTN8600-I








































































Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands

Raisecom iTN8600-I, Product Description

Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands