Raisecom iTN8600-I Product Description Download

Page: 36 / 71

Raisecom
iTN8600-I (A) Product Description

4 Technical specifications

Raisecom Proprietary and Confidential

Parameter

Description

MTTR

< 2 hours

4.4 EMC specifications



Pass the EMC Class A test.



Comply with the CE certificate.

4.5 Security standards



Comply with UL/EN 60950-1 standard.



Refer to IEC 62368-1.



Meet UL requirements.

4.6 Environmental requirements

The environmental requirements should comply with the following standards:



NEBS GR-63-CORE: Network Equipment-Building System (NEBS) Requirements:
Physical Protection



European Telecommunication Standards Institute (ETSI) EN 300 019

4.6.1 Storage environment

Climatic environment

Table 4-3 lists requirements for climatic environment for storage.

Table 4-3

Requirements for climatic environment for storage

Parameter

Description

Air pressure (kPa)

86–106 (excluding the mine shaft environment)

Temperature (°C) (altitude: 0–1800 m)

-45 to +70

Relative humidity (indoor)

10%–90%

Solar radiation (W/m²

)

≤ 1120

Heat radiation (W/m²

)

≤ 600

Wind speed (m/s)

≤ 20

Summary of Contents for iTN8600-I








































































Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands

Raisecom iTN8600-I, Product Description

Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands