Raisecom iTN8600-I Product Description Download

Page: 60 / 71

Raisecom
iTN8600-I (A) Product Description

5 Appendix

Raisecom Proprietary and Confidential

Figure 5-10

Stripping dimensions and connector

terminal screw

6.5mm

20mm

M2 fixing

screw

-48

RTN

Wiring stripping

dimensions

AC power cable

The AC power cable transmits 110/220 VAC power from the power souring equipment to the
AC power terminal block of the iTN8605, and supplies power to the entire device. The
iTN8605 uses different AC power cables in different countries or regions.

Regional standard

Cable name

POL-AC-European 3-pin/receptacle-AC power cable-0.75mm2-
1.5m /RoHS

POL-AC-American 3-pin/C13 connector-18AWG-1.5m/RoHS



CE-standard AC power cable

The AC power cable which meets European standard is composed of the European 3-pin plug

and C13 connector, as shown in Figure 5-11.

Figure 5-11

European AC cable

Technical specifications

Table 5-19 lists technical specifications of the European AC power cable.

Summary of Contents for iTN8600-I








































































Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands

Raisecom iTN8600-I, Product Description

Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands