4
2. Route the cord through the grooves on
the bottom of the base.
3. Plug the modular cord’s other end into a
modular phone line jack.
4. Insert the supplied AC adapter’s barrel
plug into the
9V DC
jack on the bottom
of the base.
5. Route the adapter’s cord through the
grooves on the bottom of the base.
Then plug the adapter into a standard
AC outlet.
Wall Mount Installation on
a Standard Modular Wall Plate
To mount the phone on a wall using the
supplied T-shape bracket, you need two
screws (not supplied) with heads that fit into
the keyhole slots on the bracket.
Ô
1. Drill two holes 3.25 inches (83 mm)
apart. Then thread a screw into each
hole, letting the heads extend about
1
/
8
inch (3 mm) from the wall.
2. Run the supplied AC adapter’s cord and
the supplied module cords through the
slots in the supplied bracket.
3. Insert the AC adapter’s barrel plug into
the
9V DC
jack on the bottom of the
base.
4. Plug one end of the supplied modular
cord into the
TEL LINE
jack on the
bottom of the base.
5. Route the adapter and modular cords
through the grooves on the bottom of
the base.
6. Insert the bracket’s tabs to the base’s
slots and align the studs with the base’s
slots. Then press the base down until it
locks into place.
tallation
7. Align the bracket’s keyhole slots with
the mounting screws and slide the
bracket downward to secure it.
8. Plug the modular cord’s other end into
the phone jack, and plug the adapter
into a standard AC outlet.
To remove the base from the bracket, press
both studs on the bracket and lift the base
from the bracket.
Use the Belt Clip
Attach the supplied belt clip to the
cordless handset (optional).
Connecting/Charging
the Battery Pack
The phone comes with a rechargeable
nickel-cadmium battery pack in the handset,
but not connected. Before using your phone,
you must connect the battery pack. Then
charge it for about 12 hours.
Ô
1. Press down and slide off the battery
compartment cover.
2. Lift the battery pack out of the
compartment.
3. Plug the battery pack’s connector into
the socket in the compartment (the
connector fits only one way). Then snap
the battery pack to the battery holder in
the compartment.
4. Replace the cover.
To charge the battery pack, power the base
using the AC adapter and place the handset
on the base. The IN USE/CHARGING
indicator on the base lights.
If the phone beeps twice every five seconds
during a call, or the screen displays
BATTERY LOW
,
«
or
NEEDS RECHARGING
,
recharge the battery
.
!
Use a pencil eraser to clean the charging
contacts on the handset and the base about
once a month.
Ô
NOTES
Ô
Wall Mount Installation on
a Standard Modular Wall Plate
Install the Base Unit away from electronic
equipment, such as personal computers,
television sets or microwave ovens. Avoid
excessive heat, cold, dust or moisture.
Connecting/Charging the Battery Pack
• This battery should remain charged up to
five days with the ringer turned on and up to
12 days with the ringer off. A fully charged
battery provides an average talk time of
about six hours.
• Place the Handset in the Base so the
CHARGING light turns on. The battery pack
is typically fully charged in 10 hours.
• You can keep the battery fully charged by
returning the Handset to the Base after each
use.
• If you repeatedly get a low battery indicator,
even after charging overnight, the battery
should be replaced.
• Be sure the battery pack is properly
connected before you try to charge it. The
IN USE/CHARGING indicator lights when
the handset is on the base, even if the
battery pack is not connected.
Ô
BATTERY NOTES
Ô
• Dispose of old batteries promptly and
properly.
• Do not mix old and new batteries, different
types of batteries (standard, alkaline, or
rechargeable), or rechargeable batteries of
different capacities.
• If you do not plan to use the phone for over a
month, remove the batteries. Batteries can
leak chemicals that can damage electronic
parts.
!
IMPORTANT
!
The EPA certified RBRC
®
Battery Recycling Seal on the
nickel-cadmium (Ni-Cd) battery
indicates RadioShack is
voluntarily participating in an
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a
convenient alternative to placing used Ni-Cd
batteries into the trash or the municipal waste
stream, which may be illegal in your area.
Please call 1-800-THE-SHACK (1-800-843-
7422) for information on Ni-Cd battery recycling
and disposal bans/restrictions in your area.
RadioShack’s involvement in this program is
part of the company’s commitment to
preserving our environment and conserving our
natural resources
