manualshive.com logo in svg

rada Pulse 120, Product Manual, Page: 33 / 48

Share
Download
rada Pulse 120 Product Manual Download Page 33

33

4. 3M

TM 

Connectors

The sensor cables on the pulse operating systems can be lengthened by using 

the 3M™ connectors included with the fixing pack. The cable to be joined must be 

to the same specification as the integral sensor cable (LAPP Unitronic LIYY). It is 

recommended that the total cable length should not exceed 6 metres.

Important! 

do not use the 3m™ connectors to shorten the cable when replacing a 

sensor. Only use the 3M™ connectors supplied with the fixing pack. After compressing 

they will release sealant, the use of any other type of connector may cause operation 

problems. cable / sheath ends must not be exposed to wet conditions and must 

terminate within a sealed enclosure or a fully sealed cable joint.

1.

  insert the wire ends into the 3m™ connectors, make sure that they are fully 

pushed into the connectors so that the ends are under the jointing blades.

 

Note!

 do not strip the wires, the jointing blades will make the connection through 

the outer sheath. 

2.

  using a pair of pliers, compress the connector to complete the connection.

Summary of Contents for Pulse 120

















































Reviews:

No comments