manualshive.com logo in svg

rada Pulse 120, Product Manual, Page: 32 / 48

Share
Download
rada Pulse 120 Product Manual Download Page 32

32

3.3 sV3022 solenoid Valve
1.

  connect the pipework to the inlet/outlet of the valve (refer to illustration). we 

recommend the use of compression/union type fittings (not supplied) to ease 

removal of the valve if required.

2. 

unscrew the electrical connector retaining screw and remove the electrical 

connector. remove the retaining screw from the connector.

3. 

lever the insert out of the electrical connector using a small screwdriver.

4. 

fit the electrical wiring through the cable gland and connect it to the terminals 

in the insert. wiring polarity is not important.

5. 

Reassemble the electrical connector and refit it to the solenoid coil. Tighten 

the retaining screw.

6. 

The SV3022 Solenoid Valve is fitted with a high power coil. A maximum of five 

sV3022 solenoid Valves may be connected to one rada pulse control box.

 

Important! 

These must be connected to alternate outputs of the rada pulse 

control box (e.g. 1, 3, 5, 7, 9).

 

each fuse in the rada pulse control box supplies a single pair of outputs (e.g. 

fuse 1 = Valve 1 / Valve 2, fuse 2 = Valve 3 / Valve 4).

 

do not connect multiple sV3022 solenoid Valves to any one fuse.

Installation of sV3022 solenoid Valve

electrical

connector

solenoid coil

cable Gland

electrical wiring

compression/union

Type fitting

Summary of Contents for Pulse 120

















































Reviews:

No comments