manualshive.com logo in svg

rada Pulse 120, Product Manual, Page: 24 / 48

Share
Download
rada Pulse 120 Product Manual Download Page 24

24

2.2 Rada Pulse129 sensor
1.

  refer to section: 

'Install the sensors, 2.1 Rada Pulse 120 and 122 sensors' 

and follow instructions 1 and 2.

2.

  make sure that the foam seal on the rear face is in place then secure the sensor 

to the wall with the securing screws (supplied).

3.

  make the connection between the 2 core cable and the rada pulse control box 

using the plug-in connector (supplied).

Installation of 129 sensor

fixing screws

wall plug

Installation of 120/122 sensors

Grub screw

cover

fixing screw

wall plug

sensor

3.

  Secure the sensor to the wall with the supplied fixing screws.

 

To prevent water ingress into the building fabric place a thin bead of silicone 

sealant around the top edge of the sensor (refer to illustration).

4.

  make the connection between the 2 core cable and the rada pulse control box 

using the plug-in connector (supplied).

5.

  fit the cover. make sure that it locates correctly over the top lip of the sensor.

6.

  fit the grub screw to secure the cover in position.

silicone sealant

Summary of Contents for Pulse 120

















































Reviews:

No comments